4GNTW4400YQ0 Amana Washer - Instructions

Watched a video on the internet.

Pulled off the dispenser. Used socket set to remove bolt. Removed entire agitator out of washer. Placed both feet on bottom of agitator and then pulled up on the upper agitator. It took some muscle due to the years of washer use. I used a flat-head screwdriver to weaken the plastic clips holding down the old bearing-driven cam. Once I got the upper agitator off, the guts were easy to pull out. Then I just re-assembled with the 3 new parts (the Cam Driven, the Dog Ears, and the Bearing-Driven Cam).

Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch and put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.

Replaced 1 of 4 of the suspension bushing. Works great.

The repair was easy, first you take out the fabric softener dispenser, you will then see a plastic cap at the bottom. the plastic cap pulls right out. Once you remove plastic cap you will see the top of a 11mm screw. Use an 11mm socket with 6 inch extension to remove the screw. The screw is a fine thread so it takes alot of turns to unscrew. After removing screw the whole agitator should pull out of washing machine. The agitator has two parts, lets just say a top and a bottom. Once out of the machine turn the agtitator upside down and tap the top part with a rubber mallet, it will fall off easily and the cam will come out with it. Once you have done this you will see how easy it is to replace the cam and put everything back together. My washer works like new. my only trouble was finding the part, until i found this web-site Part Select, The Whirlpool site did not even offer a diagram for my washer. So thank you Part Select from me and coworkers for the part and fast delivery. I can now wash my clothes again. Yeah !!!

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Removed top cap and one nut from agirtator then removed complete assembly. Replaced new assembly nut and cap.

Easy, just followed the repair video. Recommend also ordering the drive belt. Bought one locally during my repair.

Went on u tube saw different video to How disassemble the top to have access to the rod. Changing one by one those rod I was in need of my wife to hold the cover while I was changing the rod.... order for suspension rod kit. Reassemble the top by sliding the cover and to snap. Screw back the panel. And it solve the problem. My wife was really happy so me. It can be done by anybody but first go on the internet to get a idea.

On my Whirlpool washing machine I first pulled off the top cap piece of the agitator. No clips it just popped off.
Second I reached down inside the agitator and pulled straight up on a dome-shaped piece that was a little difficult to get out but it has two metal handles that allowed me to hook my fingers around it. Once I pulled hard enough it came out.
Third I used my left hand to hold the base of the agitator still while using a socket to break lose the big nut down inside the agitator. After getting the nut off I pulled straight up on the base of the agitator and pulled the whole unit out of the washer. Here's where I got stuck. I wasted about 45min trying to pry open the little plastic tabs down inside the agitator that hold the cam in place. What I finally did that I should have tried first to step on the base with both feet and pull up hard on the agitator cylinder (that has the spiral fins on it) at it popped off and popped off the cam at the same time. After that reassembling everything with the new cam was straight forward (just reversing all the steps).
I hope this helps you.

First I removed the top of the agitator and then used a socket and ratchet to unscrew the bolt and put the new one on and tightened up the bolt, real easy.

Removed the softerner dispenser and the inner cap and seal. Removed the mounting bolt. Pulled on Auger and entire agitator came out. I needed to separate the parts. It said to stand on the bottom and pull on the top. I am an "older" woman and after wrestling with it for an hour without success I waited for my nephew to come by to separate the two pieces. When he did, it popped apart and all the parts went flying. Poor guy thought he had broken it. After conviencing him that that was what I wanted it to do, he left. Dirrections weren't very clear as to what went on first and I didn't have the convience of seeing it before it flew apart. Finally put it together and replaced the bolt. To no avail, something was wrong. My sister was making the same repair at her house across the street so we double teamed it. She came over and told me that I needed to put the Bottom agitator in the machine, then the spacer thrust, then the auger, then the assembled cam and cam dogs, then the bolt. All went well and was working.......so we thought. Started a washer load and the washer started leaking water. Don't know why, still don't know why. All I did was remove everything, put it back the very same way, and it hasn't leaked since. Go figure!

first I removed the fabric softner and water seal from center of agitator, then I removed the bolt holding it on. All I had to do then is install new agitator with old bolt place water seal and fabric softner container back on and start washing clothes again. Very simple.

First, I checked the belt before ordering and then decided to order the belt, capacitor, and clutch assembly (if I needed to replace). I replaced the belt noticing the older belt came right off and new one was tighter going on. I replaced the capacitor since I had it handy and it can be known to cause this smell also. After setting washer back up and started a cycle I noticed the spin cycle would not start properly so I thought maybe the capacitor (new one) was faulty or just not the exact match even though it was said to be. I replaced my older capacitor back on and again ran cycle and it ran great. Thus I decided to send the parts which were not used. I would recommend this site as I have used them in the past before on other items. They ship fast and have a great return policy if parts not used.

First I removed the fabric softner dispenser. Then I removed cap took screw out removed agitator asseembly put new one in then I put screws back in.