DLW330RAW Amana Washer - Instructions

remove agitator then remove center bolt from hub, match bolt with longer bolt so that gear puller will work. install bolt and gear puller and twist top of gear puller until hub is removed. remove old seal ,use sand cloth or emery cloth to remove all deposits from shoulder. make it shinny, use some dawn dishwashing soap to line the inside of the new seal at the bottom and slide into place.take a piece of 2" PVC about 4" long and slide over the top of the seal and tap with a rubber hammer until seal is seated firmly on shoulder. look to see that there are no gaps with a inspection mirror or a make-up mirror.If their are no gaps ,install the hub and tap on the new hub with the rubber hammer. the hub will not seat all the way down so use the old bolt to pull it down, now take out the old bolt and install the new one, this is because the new one has lock tite on it ,your done!

First I tried to lift the lid on the top of the washing machine. I eventually realized this model doesn't open up from the top. I removed two screws on the very bottom of the front panel of the washing machine. Then pulled gently downward to release the front panel from the two clips holding it in at the top. Once the front panle was removed, I found I could easily access the drain hose and disconnect it from the pump by loosening the clamp screw. (Be aware, there is still water in the hose and pump that will run out onto the floor; I had a bucket close by and tried to catch most of this water, but its somewhat futile.) There are two additional hose clips one underneath the tub, and one on the back panel of the washer that hold the hose away from other mechanical parts. Once the hose is freed from those clips it could be removed from the washer by feeding the hose out the back panel. The new hose was then inserted and fed down inside the washer, attached to the pump, tighten the hose clamp screw, clip the hose to the other two clamps so it is out of the way of other parts, reattached the front panel and you're done!

One other note about PartSelect.com...A few days after ordering my part, I had an "International Transaction Fee" show up on my debit card statement. I panicked thinking my card number had been stolen only to call my bank and find out PartSelect is based in Canada.

pulled cover off face of machine to gain axcess
saw pulley had come off brass sleeve( Bad design should have had a larger washer on bottom to help support pulley ) would of prevented this problem
Removed motor to gain axcess to pulley and belt change . Keep a towel near by to catch any extra water still in hoses on lower pump

I have call the number that is at the washer top they recomended 2 maytag repair places i call the 1st one and 2nd one charge 75 dollars for estimate and 2nd 65.00 i pay 65 dollars for him to come to my house and turn the washer on for 2 sec. and gave me an estimated of 839. w/that money i can buy another washer i call my dad and ask him to help me to pull the washer apart and thats how i find out it need it the pump search the web and find partselect order and i was expecting the part to arrive 5-6 days later and to my surprise i receive the parts next day w/outpaying next day shipping, and start the repair. Remove the screws from the front of the washer to get access to the bottom of the waher where the motor is the pump is located under the motor. remove 1 of the springs the holds the outer tube, remove 4 more screws to pull the motor out, remove the shield motor and pull the pump out replace w/new one and put everythig back together.( recomendation) pay attention to how thing are before you start if possible keep screws and label separate like top screw,middle screws etc....... thank you Lidia

Removed front panel; loosened hose clamp at pump; removed existing drain hose. Easy part.
Installed new hose at pump and tightened hose clamp. Somewhat difficult.
1. Your hose design should be solid flexible rubber hose instead of corrugated type. Had rough time snaking hose to the pump.
2. Your future designs should have rubber hose or hard piping to the exit hole on the back panel and terminated in a male fitting, then connect flexible hose from fitting to drain line. Similar to "hot & cold " water connections.
3. For future customers- care should be taken installing the "black" portion ; it kinked on me 2 or 3 times because you have to keep rotating the entire hose to keep the "black" portion straight.

First, I printed all the diagrams on the Partselect site so I would know how things went together.

I removed the two screws at the bottom of the front panel and removed the panel by pulling the bottom out allowing the top to come off he retaining clips. I then used pliers to remove the two springs holding the front of the washer tub to the base. Then I removed the spring that attached to the idler arm and the motor. (I also took digital pictures of everything in case I forgot the routing of the belt, the location of springs, etc.) Next I loosened the clamps holding the inlet and outlet hoses to the pump. The water loss was minimal as my washer was still functioning, but I could see that if the washer died with a full tub, there could be a lot of water. I then slipped the 2 hoses off the pump. Next I removed the four bolts holding the motor/pump combo from the frame. I unpluged the electrical connector (on the top left side of the pump....it has a locking tab on top that must be depressed to remove it). Then tilt the bottom of the motor/pump combo up and forward to allow it to come out of the machine. Please note the routing of the belt for replacement later.

The pump has 3 screws (torx) that attaches it to the motor. In most cases, it seems the pump will seize to the motor shaft due to the heat of the motor over time. Since the pump is bad anyway, I simply chiseled it off the motor shaft using a flat blade screwdriver and hammer. It is tempting to put the screwdriver between the motor pulley and pump, but this will only bend the pulley.......I know from experience. It will take several good whacks but eventually the pump will come off. In my case the pump had leaked enough that the end of the motor shaft was slightly pitted and corroded. I took a file and cleaned up the end so the new pump would slide on properly. I also put a small amount of machine oil on the motor shaft and wiped it good just to make the pump easier to mount. I then slide the pump on the motor shaft, replaced the 3 torx screws (make sure you have the belt in the right position.....one run of it goes inside the pump mounting stud.) I then reversed the process.....remounted the motor/pump combo, reattached the power connector, replaced the belt on the pulley beneath the drum, reattached the idler tension spring, reattached the 2 hoses and clamps, and reattached the 2 drum holddown springs. I then inserted the top of the front panel on the two clips and tilted it back down into place and replaced the 2 screws at the bottom front.

All in all, it was very easy..........taking only an hour or so. My belt was still in good condition, but I could advise you to go ahead and replace the belt while you are in there. It also could be practical to replace the pulley on top of the pump, as it is easy to bend. I did bend mine, but managed to straighten it back out.

After completing the repair, the washer works perfectly with no leaks.

I figured that the best thing to do is buy an adapter for the standpipe and now no more overflowing.

Unplugged washer and disconnected water lines and drain hose from wall. Removed the two Screws at bottom front panel and tilted lower portion out at bottom and removed panel. Removed screw on each side under to top panel, removed three phillps screws on top control box to tilt the top box forward and unplugged the wiring harness,unscrewed the ground wire, pulled off water level hose, disconnected switch power wire connections. Slid control forward and removed. Found broken spring and anchor slit rusted thru where spring attached to base. Cut a 1/2" strip of metal from a 2x4 metal strap and attached to bottom side of base with screws, set washer uprite and tilted top panel to attach springs to tub. Inserted spring at bottom and pulled spring into slit on side of tub with a heavy gauge bent wire, bent like the top of springs being replaced. Reconnecd wiring to to panel box & Hose, srewed in place at top, reattached screws uhder top front left and right and inserted front panel at top and attached two front screws at bottom. Reattached hoses and plugged in unit. checked for spin, o.k.

I used your great video for pointers as to what to do. I took off the front, raised the top, vacuumed the whole thing up, that took quite a while. Took out the drum. Did more cleaning. Then took off the old retaining rings with retaining ring pliers, took off the old drum rollers and support. Replaced with new roller supports, washer, roller, washer and retaining rings. Then I replaced the belt. Tested it and turned the wrong way and it came off. Replaced and tested it again and I don't know why but it came off. Replaced the belt again, tested fine. Then I replaced the felt pads and glides, they were worn. I ended up asking my husband to help hold the drum so I could get the front back on. Replaced front and door. Tried the dryer. Works great AND very, very little noise. Note: when taking the wiring off the light and the door switch, I took photo's of those places with my cell phone and had them to look at to make sure the wiring was correct.

I tipped the tub towards the area where the springs were and connected them. They broke because that particulary area seemed to get moisture and they rusted. Truthfully, although the machine still works, its last days are just down the road.

simple as removing front panel from washer held on by two screws and the hose was right their. Took a few minutes to disconnect it from the pump and pull it out through the rear, then feed the replacement in and reverse the process. Piece of cake. Thank you.

this machine seems good to work on because almost every thing is done from the front without pulling it away from the wall. Removed front lower cover by removing two screws. There are three brake pads with two bolts each. applied silicone grease to each pad and put it back togather

took the belt out and took the thing out and fixed then put it back.

1. unplug unit 2. remove front access plate 3. disconnect tension spring on drive belt 4. remove 4 motor mount screws 5. disconnect intake and return lines from pump using a pliers to decompress compression rings and sliding lines off. 6. Manipulate motor and loosen drive belt from bottom of tub and let it hang. 7. tilt motor bottom out exposing pump and remove 3 screws using TREX head driver and remove pump. 8. install new pump

Unplugged washer from power source. Dissconnect the water supply. Take off lower panel. Undo big spring. Remove 4 bolts that hold the motor. Unplug the motor. remove motor and belt. While on the bench I regreased the Idler pulley. then reverse the procedure to reassemble