NTW5205TQ0 Amana Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gregory from Kent, OH
- Parts Used:
- WP63907
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Washer tub off balance and noisy
The repair was fairly simple and while it made the spin operation quieter and and a bit more stable, it still gets out of balance. Disconnected power, shutoff supply lines and disconnected them from the unit.
Laid washer on its front and replaced the two more visible springs fairly easily from underneath using a little leverage with a 2 x 4 to take any residual tension off the springs.
Then I turned the washer over on its back (gently and with a little support (board or old thick towel) so the weight of the unit didn't rest entirely on the water intake connectors
Again, lifted the tub with 2 x 4 and disconnected the power and control connector to the motor to make a little more room to get to the spring.
If you do this, be sure to re-connect that connector before you put the washer back and test, otherwise it will fill and then sit.... I had to siphon the tank out, disconnect everything, flip it over and re-connect that power connector!! After that the unit ran better than before, especially on the spin cycle. Over all this washer is 15 years old and worn a bit so we are still careful not to overload it and balance the loading as much as possible. Large bedspreads and king size sheets or mattress covers will always spin out of balance but for 90% of regular washing it was an improvement.
Laid washer on its front and replaced the two more visible springs fairly easily from underneath using a little leverage with a 2 x 4 to take any residual tension off the springs.
Then I turned the washer over on its back (gently and with a little support (board or old thick towel) so the weight of the unit didn't rest entirely on the water intake connectors
Again, lifted the tub with 2 x 4 and disconnected the power and control connector to the motor to make a little more room to get to the spring.
If you do this, be sure to re-connect that connector before you put the washer back and test, otherwise it will fill and then sit.... I had to siphon the tank out, disconnect everything, flip it over and re-connect that power connector!! After that the unit ran better than before, especially on the spin cycle. Over all this washer is 15 years old and worn a bit so we are still careful not to overload it and balance the loading as much as possible. Large bedspreads and king size sheets or mattress covers will always spin out of balance but for 90% of regular washing it was an improvement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Asheville, NC
- Parts Used:
- WP387240
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Washing machine shakes violently during spin cycle
Removed four screws that hold the top control panel to the base and hung over the back panel in order to remove the main wrap-around body of the machine. Took off top plastic ring fastened to side of tub then removed old Balance ring. Installed new balance ring. Unfortunately, this did NOT fix the problem. This was a suggestion from Justanswer.com and failed miserably. Does anybody know how to fix this problem? And it's not the springs or the little plastic shims around the base OR the cross coupling to the motor...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Woodland Hills, UT
- Parts Used:
- WP63907
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Washer basket off-center and wobbling during spin cycle
Remove the washer case/enclosure to expose all the internal parts. Lie on the floor and with pliers and a strong arm. Remove and replace each spring one at a time. Pretty straightforward.
Was this instruction helpful to you?
Thank you for voting!
washer would not spin clothes
Followed the video instructions. Had no problems. The video was accurate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debby from STATESVILLE, NC
- Parts Used:
- 285811
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Washer would drain but not spin
Pulled up on fabric softener dispenser and removed it. Had to use pliers to remove cap and seal to get access to the bolt holding the agitator in.
Realized my socket extension wasn’t long enough so went to Lowe’s and bought another.
Was unable to hold the bottom of the agitator to keep it still and get enough leverage to remove the bolt. I poured hot water over it and then climbed into the washer and used my foot to hold the vanes still while I removed the bolt. Once I got the agitator out, the rest was a breeze. Separated the top of the agitator from the bottom by placing it on the floor, using my feet to hold it down and pulling up to remove the top part of the agitator.
Turned the top of the agitator upside down and removed the cam and feed dogs. Assembled the new one and held the agitator top horizontally while placing the new part back in.
Reassembled the top and bottom of the agitator and put it back into the washer. Tightened the bolt, replaced the cap with its seal and pressed the fabric softener dispenser back into place.
Realized my socket extension wasn’t long enough so went to Lowe’s and bought another.
Was unable to hold the bottom of the agitator to keep it still and get enough leverage to remove the bolt. I poured hot water over it and then climbed into the washer and used my foot to hold the vanes still while I removed the bolt. Once I got the agitator out, the rest was a breeze. Separated the top of the agitator from the bottom by placing it on the floor, using my feet to hold it down and pulling up to remove the top part of the agitator.
Turned the top of the agitator upside down and removed the cam and feed dogs. Assembled the new one and held the agitator top horizontally while placing the new part back in.
Reassembled the top and bottom of the agitator and put it back into the washer. Tightened the bolt, replaced the cap with its seal and pressed the fabric softener dispenser back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mathieu from Palmetto Bay, FL
- Parts Used:
- 285565
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Upper Agitator Ratchet Broken
1. Remove Top Cap.
2. Remove Seal Cap.
3. Remove 7/16 Bolt
4. Lift out Old Agitator
5. Put in NEW Agitator
6. Replace 7/16 Bolt
7. Replace Seal Cap
8. Replace Top Cap.
9. Sit back and enjoy your clean clothes
2. Remove Seal Cap.
3. Remove 7/16 Bolt
4. Lift out Old Agitator
5. Put in NEW Agitator
6. Replace 7/16 Bolt
7. Replace Seal Cap
8. Replace Top Cap.
9. Sit back and enjoy your clean clothes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Poplar Grove, IL
- Parts Used:
- 285785
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Washer would'nt spin
diconnected water supply and discharge, unplugged the unit, removed the aggitator, laid the washer on it's back, romoved the hoses from the pump, took out 3 bolts, removed the motor/transmission and replaced the clutch and put it all back together.
Was this instruction helpful to you?
Thank you for voting!
Spider coupling between motor and transmission broken
Followed the video on the website. I removed the hoses from the pump rather than removing the pump as suggested in the video. Then separated the motor from the transmission and replaced the coupling; then reattached the motor and hoses. Lining up the washer cover and clamping it back on was the most trouble. But all in all, a easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- clinton from selah, WA
- Parts Used:
- 285753A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
noisy
just like video showed really helpfull
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from madison, SD
- Parts Used:
- WP8318084
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
washer would fill but not run
After reading other comments about lid switch replacement , I knew the front of the control panel would move forward and lift off. Although none of the descriptions mention the steel clips that were also use to hold the cover down. It does take quite a bit of presure to pry these up and loose before panel would move forward. Would recomend putting tape on both washer and screwdriver to protect washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernest from Midlothian, VA
- Parts Used:
- WPW10001130, 285753A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
No agitation, No spin, pump OK
I was familiar with the Kenmore / Whirlpool direct drive mechanism but at first I could not determine how to release the console. I finally found the end cap trim pieces would pop off revealing the 2 screws that hold the console in place. After removing them the console flips up and over the backboard. I then removed the 2 clips that hold the cabinet to the backboard, unpluged the lid switch connector and then tipped the entire cabinet forward and off the frame. This gives you access to the entire washing machine mechanism.
Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires.
The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.
Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires.
The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JANET from GERMANTOWN, NY
- Parts Used:
- WP8317926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
The water intake hose had a hole and was leaking. I think a rat chewed it.
I first watched a YouTube video on how to open up the machine. It was a breeze. I removed the part the hose attaches to where the water comes out and into the tub. The hardest part was removing the old hose clamps. Had I known I would have used new clamps. I took off old hose and replaced with the new one, it took longer because of the clamp issue. Otherwise it went fairly easy, to my surprise. Even tho I am a 70 yr old woman I will try to fix what I can. Doing this saved me at least $600. For a new washing machine. I'm so proud of myself.
Was this instruction helpful to you?
Thank you for voting!
washer would not spin to extract vwater
will not go over step by step here as there are already a multitude of stories on site with exact situation as mine who have already done so.. What I will say is that PartSelect is easily the absolutely best site on the net for a complete problem diagnosis to finished repair experience. Just input your model # and describe the problem and you get instant diagnosis probabilities along with access to a long list of customer Q & A and reviews, along with step by step videos on diagnosing, dis- assembling, and re-assembling along with links to all parts needed and also some secondary tips along the way. The prices are fabulous (example: I got a clutch assembly kit with several parts and 2 additional parts as a just in case for $55 shpg incl, while my local appliance parts place wanted $59 plus tax for just the main part in my assembly kit with a no return policy and no part guarantee, plus it was only 1 day more to have PartSelect pkg arrive than I would have gotten part from local store). This site is FABULOUS !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Edgewood, TX
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
top agitator would not operate
unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Whiteman AFB, MO
- Parts Used:
- WPW10072840, 285565, WP358237
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Upper agitator would not turn
First I removed the fabric softener dispenser. I removed the inner cap seal and agitator retaining bolt. Then I firmly pulled up on the agitator to remove the complete agitator assembly. I replaced the inner cap seal and installed the new agitator bolt with rubber washer. I placed the new agitator assembly on the drive shaft and tightened the bolt. Lastly I installed the inner seal and the fabric softener dispenser. The total time spent was around 10 minutes.
Was this instruction helpful to you?
Thank you for voting!