P75751-1W Amana Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Martin from Grayslake, IL
- Parts Used:
- R9900543
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench set
Water leaking when water level is set above medium. Wash tub spinning when during agitation cycle.
Three brake pads are located just above the drive pulley and space symmetrically around the brake wheel. Remove the one screw per brake, slide brake out of brake wheel and replace with new brake. Apply silicone grease to new brakes before installing. Tools: 5/16 boxed end wrench.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Calvin from Bethel, AK
- Parts Used:
- WP207166
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
washer worked but would not advance to next stage
Remove front panel. Then remove top of washer, two bolts at front of top. Then remove two bolts that hold switch assembly to top on right side of top. Switch gets pried out. It just sits in with small pins holding it in place. Wire connectors hold very tight. Install is reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RAFAEL from CENTERVILLE, GA
- Parts Used:
- WP207166
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burned out part
Good.
Was this instruction helpful to you?
Thank you for voting!
Washer stopped pumping discharge water
The only real problem was one spring loaded hose clamp to the rear of the pump. If it had been a standard clamp like the others I would have cut the repair time down by 2/3rd's. I did find that by removing one of the long wash drum springs, I then had more room to get my channellocks back there to get the stupid clamp to compress, and then used a screw driver to push the clamp back off the the connecting port. I replaced the camp w/ a standard clamp and the reassembly went quick and easy. Note, If you replace the pump drive belt with a new one, you WILL have to adjust the belt tension after a few minutes use.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Anchorage, AK
- Parts Used:
- R9900543
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Agitator not working. Found worn brake pads which allowed tub to turn without agitating
After removing the front panel I was able to reach the bolts holding the brake pads in place. Without the above mentioned ratcheting end wrench it would have been very difficult to start the bolts while replacing them. I would probably consider removing the motor if I had to do this again. It would give a lot better access. no real difficulty other than hard to reach.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Meg from Owensboro, KY
- Parts Used:
- WP22001682
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The washer stopped during the rinse cycle - and full ot water.
I turned the dial to other selections and nothing worked, no power. I checked the fuse box, but nothing was off, and then I checked to make sure electricity was working with a light bulb. I googled the situation and came across this site and read other posts as they sounded exactly like what I was experiencing. I ordered the complete lid assembly not just the fuse. The item arrived quickly in two days. After about an hour, as it was pretty easy to replace, the washer was working again! Thank you all for posting, as it saved me at least a couple hundred dollars.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Los Angeles, CA
- Parts Used:
- WP22001682
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Blown switch
The hardest part was actually finding the right part. It was easy to take of the control panel. make sure you unplug and plug in the correct wires....
I thought that would be it, but after doing that you need to fine adjust the whole assembly so that the timers and automatic switches work well.
That's about it.
I thought that would be it, but after doing that you need to fine adjust the whole assembly so that the timers and automatic switches work well.
That's about it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from SEDONA, AZ
- Parts Used:
- 22003428
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench (Adjustable)
Threads on old legs had been damaged in moving to new location.
Removed the damaged legs, replaced with parts from this site and leveled the washer .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dewey from Northport, AL
- Parts Used:
- WP22001682
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Motor quit running.
Took a look at the new door switch assembly, used a socket wrench to remove the old, took wires off of old and attached them to the corresponding terminal on the new. attached the new assembly inside the top panel. Works!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from NASHUA, NH
- Parts Used:
- WP89503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Leaking water inlet hoses.
Removed the old hoses and screwed on the new hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from ROUND LAKE PK, IL
- Parts Used:
- WP27155
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Water pump motor belt broke
It was easy, All we had to do was loosen up the tension on the pump, put the new belt back on and put the tension back on the pump motor by sliding it to the side and re tighten the screws to hold the pump tight.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Angels Camp, CA
- Parts Used:
- WP207166
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
washing machine would not turn on
I removed the top cover that has the controls .Then started to voltage check the circuit (diagram was inside top cover) starting from L1 (had power cord pluged in) noted power was not going through the Check switch after tapping on the switch it started to work. the switch was intermitent so replaced with a new one from your company. works good now .Greg Gran
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deanna from Fort Lauderdale, FL
- Parts Used:
- WP22001650, WP207166
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Wrench set
Many problems
It would seem that my unhappy washer decided to
have a multiple component breakdown. after replacing one part after another, my baby runs like new. parts arrived quickly and installed easily, it was all the diagnostic that took the most time. the forums were quite helpful.
have a multiple component breakdown. after replacing one part after another, my baby runs like new. parts arrived quickly and installed easily, it was all the diagnostic that took the most time. the forums were quite helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Newport News, VA
- Parts Used:
- WP22001682
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Bad lid switch assembly
Pulled the switch assembly cover off. Removed the screws that held the lid switch assembly on and replaced the assembly.
I just want to say that the online exploded view of the parts list was very helpful. I really needed pictures and your website had them. Also the service delivered my part very swiftly and ordering was easy. If I ever need appliance parts again I will order them from your website.
I just want to say that the online exploded view of the parts list was very helpful. I really needed pictures and your website had them. Also the service delivered my part very swiftly and ordering was easy. If I ever need appliance parts again I will order them from your website.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John H. from Marysville, OH
- Parts Used:
- WP207166
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The washer would fill, but would not cycle
I found the electrical prints in the control panel. I found the door and check switch, and used my volt meter to determine which one was bad. It was the check switch, so I went online with PartSelect and ordered what I needed.
I had the model and serial numbers. So it was really easy to find the replacement part. It arrived in just days after I ordered. We are back in business. Thank you for your service, John Gamble, Marysville, Ohio
I had the model and serial numbers. So it was really easy to find the replacement part. It arrived in just days after I ordered. We are back in business. Thank you for your service, John Gamble, Marysville, Ohio
Was this instruction helpful to you?
Thank you for voting!