AAV2200AJA Admiral Washer - Instructions

Turned water off,tilted unit forward,removed lower rear cover,removed belt,laid towels around ,removed inlet hose and exit hose off pump,removed 3 screws holding pump,removed pump and installed new one,reversed order of disassemble, has been running great ever since.

I followed the instructions that other posters suggested. The springs were the toughest part to remove and reinstall. Having my wife push the tub enabled me to use vice grips to get them back on. Read about the coins or washers to spread the springs too late... would have helped. Running a wash now and it's spinning great and no noise!

I tilted the machine on it's back to remove the drive belt. You could feel the friction in the pump when you turned the pulley. I set the machine back down and removed the back cover (4 screws). I removed the two hoses with a pair of pliers. I used a small socket set to remove the three mounting screws. I ordered the pump. I reversed the process to put it back together. It took about 35 minutes to determine what the problem was and to remove the pump. It took about 20 minutes to put it back together.

Removed front of washer following instructions on partselect.com (used putty knife to release catches). Removed hoses and belt from pump, then removed and replaced the pump. Reattaching the belt was the only awkward task.

Remove tub assembly per snubber replacement procedure.
Place tub assembly on top of a milk crate open-side up.
Support tub assembly on milk crate with 2x4's to protect pully from damage.
Remove agitator from tub assembly.
Press down on tub assembly cap, release tabs and remove tub assembly cap.
Remove inner tub from tub assembly.
Mark tub frame with location of outer tub air bell for ease of reassembly.
Remove outer tub from transmission assembly.
Replace inner tub gasket
Replace outer tub gasket

Problem encountered was that the replacement tub had a defective air bell. The washer consequently did not detect fill level and subsequently overflowed flooding the laundry room. The bell looked ok visually. Blowing into the air tube while plugging the inside hole with a finger revealed a pinhole leak in one corner of the PP weld. PartSelect was prompt with replacement, but the job had to be redone in its entirety.

Always test the air bell before installing an outer tub.

I pried up the fabric sotener cover on top of the spindle with a screwdriver and removed it and softner cup holder-it twisted off. I then replaced entire softener unit which I had ordered.

Remove the metal plate in back of the washer that 3 screws. I use a vise-grips to remove the two clamps.One on other the tub side and the other the pump side. Pull the old hose off the tub side and the pump side.Use the old clamps to put the new hose on.

I ordered the replacement pump assembly (water pump)for my Atlantis model maytag washer, removed the old one, installed the new one and works like a charm. The only difficulty I had was trying to figure out how to remove the cover on the front of the washer, to remove the clips, it slid side to side instead of popping out, found the instructions on-line, NO instructions came with the pump but if you have any common sense when it comes to repairs it was easy to remove and install the new part.

I pulled the top ofthe washer up, I disconnected the cold and hot water hoses, took the 2 bolts off with a socket and pulled the water valve from the top. I used the pliers to take the pressure ring off and pulled over flow hose off. I pulled the four wires off with pliers. Put the new water valve in reverse order...easy.

Tilted washer back and removed belt
Lifted front of top and propped up
Unscrewed two screws and removed front of washer
Disconnected two drain lines from tub
Disconnected 6 springs from tub
Removed tub
Popped off bottom plastic cap
Removed locking ring
Slid off gear from shaft
Unbolted screws from snubber support ring
replaced snubber
Put everything back together in reverse order

Worked like a champ!!!!!

I had to raise the top of the washer and take off the front pannel. It was not too hard to replace the pump except that it was in the back corner and it was hard to reach the bolts to remove and install the new pump.

Raised washer. Identified problem. Removed from panel, gaining access to drain pump. Removed hoses, replaced pump. NOTE: I used blue Loctite on pump mounting bolts. Reinstalled from panel, lowered washer, cleaned drum. Ran one (1) cycle with hot water and bleach ONLY.

The Clamps for the hoses were difficult to get to, otherwise was a simple replacement job, involving clamps and screws and bolts.

Had wife balance washer on front edge while I accessed working parts from bottom of washer. Removed drive belt and turned agitator pulley, transmission pulley and drain pump pulley by hand. Drain pulley hard to turn and shaft had play in it. Ordered new drain pump and replaced upon receipt. Very few fasteners to remove and replace pump assembly. Drive belt was easy to remove and replace. Recommend also replacing drive belt on a washer this old.

1- Unplug unit 2-disconnect water hoses 3-put unit in open area so you can work on it. 4-Open top cover with screw driver 5-take off front cover with appropriate socket 6-lay unit on it back to get access to the drive belt (take off). And take off water hose with plyers. 7-With vise grips take off the six springs. 8-Take tub assy out,and lay it on the floor upside down. 9-Loosen the screws to take out the old snubber ring, note ( when lossening screws,keep your finger on the bottom of the screw ,so you can feel how far to back the screws out,just enough to have access to the snubber ring,to take out,and install new one. )Remember not to take screws out completely. The unit is under spring tension. 10-Put washer back together in reverse order,and problem solved!