UE8230 Speed Queen Washer Dryer Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carl from Uncasville, CT
- Parts Used:
- W10169313
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dryer not turning on.
Researched the common problem with "dryer not turning on", and tested the top three problems. Removed the dryer front casing and door, unbolted front dryer plate. Used a volt meter on two of the temp gauges, which were fine. Removed the upper back plate of the dryer to the wiring for the knobs and buttons. Used the volt meter on the dryer start button, which was also fine. Went back around to the front and removed the door switch. Tested it with the volt meter and bingo. Replaced that part, dryer works like normal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from Arlington, TX
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Door Latch broken
Ordered part ( door latch ) flowed instructions easily fixed same.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from East Berlin, PA
- Parts Used:
- WP28808
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Washing machine was making a banging noise
Turned off water & unpluged ac power. Removed 2 screws on front panel. Removed panel. Found peices of V belt. Removed 4 screws from electric motor which allowed the belt to come out. Ordered new belt on line. Received the item in one day. Reversed the above sequence above. Now the washer is running as good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from La Crosse, WI
- Parts Used:
- WPY54414
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
replaced Idler pulley and bearing
Removed the front of the dryer. Took out the drum. Now everything inside is easy to get to. You do not need to remove the top. Upon inspection we found that we also needed to replace both felts, teflon guides, drive belt, and both support rollers ans shafts. Basically we rebuilt the dryer. It's quiet now and working like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daral from Merrimack, NH
- Parts Used:
- WPY54414
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Idle pulley frozen
Once I realized the drum was to be removed, the actual repair was not difficult. Because of the location of the pulley, it's best to tilt the dryer. Snap ring pliers are required to remove the retaining ring on pulley. I pulled the damaged pulley from the bearing. A small gear puller was needed to removed the frozen bearing. Lightly oil the new bearing. Installing the drum is a challenge because of the loose belt. I used paint tape to hold the belt on the drum. Download the service manual for good exploded parts views.
Was this instruction helpful to you?
Thank you for voting!
the motor quit working
i took the front off the dryer took belt loose took the tub out the plastic nut on the blower wheel striped out so i took the blower housing apart along with the motor got vise grips on blower wheel replaced motor blower wheel belt and belt tenchinor and spring cleaned all the lint put it back together works fine
Was this instruction helpful to you?
Thank you for voting!