MLE20PDBYW0 Maytag Washer Dryer Combo - Instructions

Remove screws, dryer sensor on screen. Put sensor back in place. Secure with screws. The way you take it off go in reverse.

Followed online video very easy and dryer works like new one....

I followed the video provided by ‘Partselect’; although it was not the exact model it was close enough to get the job done with high confidence.

Just follow the repair video, it was easy!

Unplugged the washer from electric outlet. Removed front cover by using nut driver to remove the two screws. Drained the water from the washer into a pan by loosening the cap on the filter. Removed the two hoses by compressing clamps with pliers. Unplugged the electric wire from old pump. Used screw driver to pry rubber feet of old pump loose from washer floor panel. Set old pump aside. Installed new pump using a little dish soap to help attach rubber feet to washer. Attached the two hoses using pliers. Plugged electric wire into new unit. Ran washer to check for leaks. Replaced front cover using nut driver on the two screws.

Removed the top cover of the washer, unclamped the intake hoses from the valves and unplugged their control wires, unscrewed the old valves and removed them from the case, screwed on the new valves, replugged the wires, reclamped the hoses, fastened the top back on.

very easy repair watched videos to diagnosed problem. Removed old sensor and rubber seal replaced with new.

Three 1/2 bolts tighten as required

Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.

Replaced the pump. Continued to get the F9E1 error. Removed and cleaned the drain pipe between the drum and the pump. Problem resolved.

Removed top of washer. Removed top front panel. Removed old front panel clamp. Removed front door panel. Removed old tub clamp. Then removed torn tub seal. Installed new tub seal. Needed two sets of hands to install new tub seal. Pretty tight installing the new tub seal around drum lip. Might be a good idea to heat up or let your new tub seal soak in water prior to installation. Once tub seal was installed, I installed new tub clamp then re-installed the door switch. After that, I put the front door panel back on. Then tightened down the door switch. Finally, I installed the top front panel and then the top of the washer.

I followed the steps from online videos to determine where the leak was coming from (cleaned the pump filter, still leaking; checked gasket and inlet hoses).

Finally, I discovered a wet area and cut on the drum-to-pump hose. When I removed the hose, I found that the culprit was a credit card that had broken into shards and slit the side of the hose. I was happy to see it was from the previous owners, which meant it wasn't my fault!

I did have a hard time removing the clamps (double-wire "rotor clip" or "spring clamps", according to Google) holding the hose to the drum and pump. This became a problem when replacing the hose as well. I was not strong enough to squeeze the ends together to loosen the clamp.

Getting the old hose off was easy enough, as was putting the hose back on. The problem was clamping it back on, as I mentioned.

I tried using zip ties, but this was a disaster! I tested it using a rinse and spin cycle, and the zip tie seemed to hold. However, the hose slid off during the first full cycle I ran and dumped at least 15 gallons of water on the floor. Clean up was not fun!

My recommendation (and what I finally went with) is to use hose clamps with the small screw that lets you tighten the clamp with a screw driver. I used that on both the connection to the drum and the connection to the pump and I've had no issues since.

Overall, it's a quick fix once you have the hose replacement and the right parts. If I'd gotten the hose clamps right away, I could have been done in 30 minutes.

Hope this helps and good luck with your repairs!

Shocks are the #1 recommendation for this problem, but they were not the solution. The problem turned out to be broken weld in the stainless tub. Three of the shocks can be replaced from the front, the one under the motor can only be accessed from the back of the machine, which means it has to be pulled out away from the wall. Taking the old ones out is kind of a pain, they don't twist off easily and there is little room to use tool. Putting the new ones in is easy, they just twist into place.

Son-in law did the work he was finished in about 20 minutes the repair guy wanted $249.00 to take out and put in. PLUS part.

Unplugged the Dryer first. Removed the two screws from the bottom panel using a 1/4 socket and removed the panel by pulling down and out. Reached behind the blower and removed the connectors from the old thermistor and then the thermistor itself by removing the two 1/4 inch hex head screws. Replaced with new part and after screwing back in, reconnected the wires and replaced the panel. From start to finish, it took me about 20 minutes.