MLE20PDBYW0 Maytag Washer Dryer Combo - Instructions

Replaced drain pump took longer to soak up water than actually replacing the pump motor with mine having the pedestal underneath I did not have to tip the washer at all so it was fast and easy. Three screws taking the front cover off a screwdriver lifting the Rubber and sliding the motor off and pair of pliers 4 to hose clamps making it a breeze.

After turning off the power to the dryer I removed two screws to the bottom front panel and droped it out of the way. I remved three screws hloding the lint screen in place just for better axcess to the element. I then removed the two wires attached to the element and then the two screws holding the element in place. I put everything back together in reverse. I also took the time to clean any dust and lint out.

Removed the front panel, removed the tub and removed the old seal. Tub seal area was scraped, sanded and wiped with acetone to ensure a clean. Bonding surface. Applied adhesive with and acid brush to get a consistent adhesive layer without getting too much in any one place. Seal was a bit smaller than the tub circumference so it had to be stretch to fit. While the adhesive was curing , I took the time to clean the contact surfaces and vacuum the lint from inside the cabinet. Reinstalled the tub, drive belt and front panel.

Took the top off and then front off and drum out . Replaced Drum roller and shaft support bolts.

First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!

First tilt the washer back so you can drain water from the lines to the pump and the pump itself. Disconnect the lines with a pair of pliers and use a screwdriver to move the rubber stopper so that the pump will move to the right. With pump now in position to lift up and out of the washer , do it so you can disconnect the wire assembly. Replace the pump starting with the wires, then slide it in place and secure it with the rubber stopper. Attach the lines and make sure they are well sitted and clamped. set on feet and you are ready to wash.

The repair went well, using the whirlpool repair manual and looking at the video from PartSelect. The machine was a bit different than the one in both the video and the manual but that did not cause any problems. The only tricky part was to reinstall the belt "blind" behind the motor, easy to pinch your fingers and also get scratched by the sheet metal edges. To make it easier for that part I supported the drum with the old belt and a bungee cord to the garage frame so I did not have to hold it up and work under it at the same time. When the drum and new belt were in place I just cut the old belt, it was going to the trash anyway.. I replaced the belt and the tension pulley, witch was not turning easy and worn by the belt. I also put some grease ( SUPER-LUBE, www.super-lube.com) on all pulleys. It took about 2 hours because I am 78 years old and have heart problems.

Replaced the most worn drum wheel any lubed the belt tension arm pulley. The noise didn't go completely away. There are 4 drum wheels. I need to order 3 more wheels and the tension arm now.

Remove top,front and panels.change thermal fuse and outlet thermistor.

all that was required was to push the catch into the slot notools needed.

I squeezed the latch catch with a pair of pliers and pushed it in the catch hole. But that was the final repair. There were two "repairs" before that. First, we used two commercial grade rolls of wide plastic tape to tape the dryer door shut each time we used it, for a year, until we ran out of tape. Second, we positioned a chest of drawers in front of the dryer and wedged a 1" x 4" against the door. Very effective. Then I broke down and ordered the $3 catch.

There is a video on this site that shows how to do the install. It is perfect and accurate. This pump is one of the easiest components to fix on this washer and it will save you money to do it yourself. Tech has told me twice to buy a new washer. This did the job. Make sure to take the time to fully drain the machine prior to doing this and make sure that you unplug your machine. To drain, just unscrew the cover on the front of the pump. If you start disconnecting hoses without draining you could have a mess on your hands depending on how much water is still in the washer. Use a shallow pan or bucket if your machine is on a pedestal. I have a floor drain in front of mine so I use a piece of foil to channel the water into it. After that, just do the install like the video. Also make sure to examine the reconnected hoses after you get done to make sure that they are solidly attached to the pump and that the base of the pump is tightly secured to the bottom of the machine. You have to secure the feet of the pump from the bottom which is why the video recommends putting blocks under the washer to have access to the bottom. Pump is great. Everything works well.

Jimmied out the latch using two screw drivers to get under the edges. Pushed the new piece in. Voila! Took 2 minutes for what my repair man told me would cost about $200 to fix. Unbelievable!!( I first watched some YouTube videos to get the idea )

replaced dryer lint screen with new.

I followed your repair video explicitly, simple fix. However, one should
be careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support!