LSE7806ABQ Maytag Washer Dryer Combo - Instructions

It was very easy to access the parts that needed to be replaced (blower wheel, belt, and glides).
1. Unplug the dryer power cord.
2. Removed the two screws at the bottom of the front dryer panel. Pull the bottom of the panel forward, which frees the retaining clips at the top of the panel.
3. Disconnect the two wires from the back of the panel, and remove the panel. The drum will be resting on the motor/blower hosuing.
4. Slide the belt off of the back of the tumbler, and remove the tumbler (have to angle it a bit, to clear the frame) and the belt.
5. Remove the thermostat cover (piece of angled sheet metal, in front of the blower unit).
6. Remove the screws from the blower housing, and lay it forward, to expose the blower wheel.
7. Remove the snap ring, and then the retaining ring from the blower wheel. Remove the old wheel.
8. Install the new wheel, then the retaining ring, and then the snap ring. Reattach the cover to the blower assembly.
9. Reattach the thermostat cover.
10. On the tumbler, drill out the rivets for each of the glides, and remove all glide parts. Install new glides.

This is a good time to complete any general cleaning inside the dryer cabinet, especially in the area of the motor. Since there is limited access to the motor itself, might help to use the blower function of a shopvac to blow out that dust.
Vacuum out all lint from around the felt drum seals.

11. Loop the new belt over the tumbler, and install the tumbler (the glides go towards the front of the dryer). Note: to keep the belt from falling off, I taped it to the drum with two pieces of painters tape..the blue tape that comes back off easily.
12. On the back of the dryer, remove the access panel, and complete installation of the belt to the idler pulley.
13. If you taped the belt to the drum....don't forget to remove the tape now. Reinstall front panel to dryer.

This was my first experience working with snap ring retaining rings. Even with snap ring pliers, they are difficult to remove without stretching them out. Be sure to order a new one with your blower wheel.

Also my first experience using a pop rivet gun ( to install the new glides). Found a rivet gun at Lowes for $9.99. Worked okay, and all rivets set properly. Good thing, because you don't get any extras with the glide kits.

After replacing the parts, and starting up the dryer, all of the clunking/squelling/rumbling noises were gone. There was a noticable smell while the new glides got broken in...smelled a bit like melting rubber. However, after a couple of drying cyles, the odor was gone.

Switch can be removed from outside of dryer and your video described the repair as having to work from inside dryer. But since wires were still attached to old switch, it could be popped out and wires switched. Since there were three wires on new switch to allow it to turn on and off a circuit, it was useful to check the resistance of the switch compressed or released to be certain I was attaching the two wires to the right two poles of the new switch. But that all required only a couple of minutes. Thank you.

For the most part, I followed the excellent repair advice already available on this site for installing these parts. Especially useful was the caution that the threaded pieces had "left hand" threads and to loosen them they had to be turned in a "CLOCK WISE" direction. My washer is 9 years old and due to calcium deposits on the threads, I did have some trouble with loosening the large retaining nut. I first soaked the nut for a few hours with a rag soaked with white vinegar. This removed some of the calcium but I still was unable to undo the nut. Finally, I soaked the nut overnight with penetrating oil and WD-40. The next morning I was able to loosen it using a drift punch and medium sized ball peen hammer. I only had one difficulty. Maybe it wasn't necessary to do so, but I wanted the rubber boot seal to be seated pretty close to the surface of the inner basket. This turned out to require more downward force than I would have expected even though I installed it dry, without use of any type of lubricant or soapy solution. Now, two weeks worth of washing and not a drop of water seen underneath the washer.

Before anything, I unplugged the dryer and tipped it over on its front. Then I removed the lower access panel and saw that the belt was broken. I removed the belt. I replaced the panel and put the dryer upright. When I ordered the belt off this site, I used one of the repair stories. With a phillips-head screwdriver, I removed the two screws below the door on the front panel. The panel is held in place by two clips at the top. Gently pull the cover off, since there are also two door-open sensor wires connected to the front panel. I removed the hex nuts holding the tumbler in place. When I started to put the belt on, and was having a bit of trouble, my neice pointed out the diagram on the bag the belt was in. From then on it was a piece of cake. I got the belt in place, replaced the tumbler and front panel, and plugged it in. Good as new!

There is one good description already posted. I would add:1)If the the nut holding the inner tub doesn't loosen easily just split it with a chisel and don't waste time. 2)Don't order extra washers to remount the outer tub, they come with the bearing! 3)While disassembled I ran the spindle on spin to make sure the brake assemlby wasn't the problem. It ran quietly and smoothly. 4)The inner bearing sleeve was stuck on the spindle and didn't want to free up. I used a rotary tool to cut a groove in the old bearing sleeve then chiseled on the groove edge and it split nicely. It was very brittle. The washer seems to work well now. Next time I see a leak I am going to repair it right away!

first i removed front panel by pulling it from the bottom and then removing the top. then i removed the agitator with a 1/4 nut driver. then i had to open top lid which is hinged and held together by two 1/2 inch bolts. after i opened up the top of the washer i had to remove the white plastic top of the inner tub. in order to remove the inner tub there is a large nut that i had to use a punch and a hammer to break it loose. don't forget this nut is counterclockwise to loosen.hint use a little wd40 due to calcium build up around nut. once the inner tub is removed you should see the rubber bushing. be sure to remove all rust and water calcium build up before installing new bushing. i used a wool pad. put everything back together the way you took it apart and it should fix your leak.

My 11 year old grandson and I did the repair together. He had a blast and I did too. First we removed a bunch of screws that got us no closer to getting the machine apart than when we started. Then I remembered from the last time I had the machine apart that there are two screws just below the door, angled as not to be visable unless you know where to look. Once we removed those the from came off. We removed the wires for the door light and heat sensor, remembering the order of the wires for later reinstallation. Then we undid the bolts holding down the top. Once the top was removed we took off the belt and removed the drum. We used the retainer pliers to remove the retainer ring from the first roller. We removed the roller and also the shaft as this roller was the noise maker and the shaft was not in reusable condition. We installed a new shaft, roller washer, roller, another roller washer and then the retainer ring. We repeated the same process on the other roller, although we did not replace the shaft as it was in good condition. It turned out I did not need to order the shaft washers as the rollers came with washers. Oh well, its not a good job unless you have parts left over when you are done. Once we replaced the rollers we commenced reinstallation. But first we had to google for diagram of the proper belt installation, which we found and that got the drum and belt installed properly. Thankd god for the internet. Once we had the drum installed we put the machine back together in the opposite order we took it apart. An operational test showed we did the job right, no more squeaking. The only injury was my grandson cut his thumb right after I gave him the speech about watching where your hand is going to end up when that bolt breaks free. It broke loose and into the metal bracket went his thumb. Oh well it was a good lesson and it was not a bad cut. All in all a good repair.

A tension sping on the motor broke, smoking the drive belt.
step1...remove front of the washer to access spring, tip washer back & prop on short 2 x 4 board. 5 minutes
step 2... remove one end of pump belt to get new bely up to drive pulley put on belt using fingers only & replaced the end of the pump belt....2 minutes

step 3...put new spring under motor & hook one end in attaching hole on motor, reach through with pliers to grasp spring to pull end to attach spot on base...1 minute

It took longer to open up the washer front & prop it up that it took to repair it. This is a siper easy repair!

Wish there was a video. I am above average handy but this one- I might just pay someone next time...The tape on the threads was a great tip but took a while to understand what they meant by putting tape on the threads. Scraping off the old pads is easy for the front one but the back pad and a half is so hard to reach to really get it cleaned. Bruised and cut knuckles on that one. Then not having the glue for the pads was a surprise and you have to get a good contact type cement that sets in 10-15 minutes or you will be waiting hours to put it back together. It was easy to put the first spring on, then the second and third got harder and harder.

I simply took the old switch out and put in the new one. The part arrived very qickly and the website was super easy to use.
thank you so much!

First I removed the two screws that held the front panel in place. Then I determined that the belt for the pump had fallen off because the drive belt was worn (and inverted) and a piece was hanging off and causing the pump belt to slip off the motor. I replaced the belt for the pump (Temporarily) to allow the tub to drain.

I replaced both belts with new belts and returned the front panel. The process took 15 minutes due to the necessity of explaining the proper use of tools to a neighbor child and allowing him to assist (required for the completion of one of his Cub Scout requirements).

Frist I removed the front cover panel via removing 2 screws. Second I disconnected the door switch wires. Third I removed the 4 screws that hold the drum onto the rollers and guides that allows access to the blower wheel assembly cover. Fourth I remover the blower wheel assembly cover to gain access to the blower wheel. Fifth using the retaining removal tool removed the retaining ring from the shaft then removed the blower wheel using plyers. Then reassembled all of the parts and enjoy a quiet dryer again.

Thank you parts select!!!

1st We pulled the washing machine from the wall and unplugged it. 2nd We tilted the maching back against the wall so that we could see all the pullies. 3rd. We removed the two screws that afix the front panel on the lower part of the washing machine and removed the panel. 4th We removed both belts and put new belts on. 5th We put all parts back in place and plugged maching back in, slide it back in place. 6th It worked like a charm and I proceeded to wash 3 loads of laundry that evening. The only tool we needed was the phillips head screw drive to take off the front panel. It took us 5 minutes to fix the machine.

I turned off the water at the main water inlet. I then removed the hose connections to the valve inlet. I removed the one screw on the plate pulling allowing me to pull the plate out from the washer body. I then removed the wires connected to the old valve placing them on the new valve (so not to be confused). I took off the small hose clamp attached to the valve. I removed the valve from the plate and attached the new valve placing the a new hose lamp on the hose (wires were already attached) screwed back to the plate in the washer body connecting the water lines and turned the water on at the main valve. I did have to run to the hardware store for the small hose clamp but that was my choice to replace the one that was existing. The washer now works like it is new.

The hardest part was figuring out how to get the front panel off of the washer. Once that was done, the pump came off easy.... 3 screws attached it to the bottom panel and 2 hose had to be disconnected. Putting the new one in was easy.