MLG19PNDWW Maytag Washer Dryer Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- lawrence from GROTON, VT
- Parts Used:
- 279834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench set
No Heat After 10 Minutes
Shut off gas removed gas valve. Removed the coil retainer and installed the new coils. Reinstalled valve and checked. Found dryer worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- reinaldo from guttenberg, NJ
- Parts Used:
- WP338906
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
no heat was being produced
Remove back panel n u can see the sensor and easy to replace thanks to the print out i was provided love this website
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- matthew from Central Islip, NY
- Parts Used:
- WP33001762
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
no heat, coil wasnt getting hot
took old one out then i had to strip the connector off new one was to big...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from Virginia Beach, VA
- Parts Used:
- WP6-3705180, WP6-3700340, WPY312527, WPY014874, WP33002535, WP315772, WP354987
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer made loud screeching noise.
After reading all the other repair stories on Partselect, by the way thank you all, I removed the door, then removed the two security hooks that hold the top secure. Then I removed the front panel. I then marked all the screws on the outer door and shroud so I could easily put it back together. I left the all the wires connected and set the shroud and outer door to the side and removed the drum belt and drum. Removed the spring off the idler arm, then using nutdriver, removed the screw that secures the idler arm to the motor. Assembled the new idler arm parts and reversed the process to put it all back together. If I would have replaced the idler arm assembly the same time I replaced the drum support rollers, I wouldn't have had to do this twice! But now I am an expert repair tech on this particular model.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Huntington Sta., NY
- Parts Used:
- 22003856
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Motor did not have the ability to rotate washing machine drum.
Removed old motor installed new motor.
Was this instruction helpful to you?
Thank you for voting!
One of the drum baffle's boke from it's mount
Removed old broken plastic grommet's and installed two new plastic grommet's. Attached new baffle using old screws. Used a short piece of picture frame wire to install the two new grommets by fishing them into place with out removing the washer drum.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phil from PROCTORVILLE, OH
- Parts Used:
- WPY312527, WPY014874, WP6-3705180, WP354987, WP33002535, WP315772, 33002459
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Squeeky dryer
Okay, first of all, just let me say, if I can do this, ANYONE can. I am not very handy when it comes to things like this. I watched online videos and they will walk you through everything. I am so pleased with the results. Quiet as can be now. Before, we would have to shut the door when it was on because the scretching was so loud! The parts on this site were far more affordable than at my local repair store and they all came right to my doorstep. Overall it took me about 45 minutes and three beers :) Good luck!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Warsaw, IL
- Parts Used:
- W10169313
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door safety switch would not close keeping dryer from running
Shut off or unplugged dryer for safety.
Slipped thin blade putty knife up under bezel of switch to unlatch from the panel and pulled forward to remove the swwitch from the dryer. Unplugged the quick connect terminals (3) from the old switch and plugged them onto the new switch. one of the terminals had gotten quite hot and darkened the insulation so it was replaced with one that was supplied with the switch. that was a cut, strip, crimp process. Placed the new switch into the panel and snapped into place.
Slipped thin blade putty knife up under bezel of switch to unlatch from the panel and pulled forward to remove the swwitch from the dryer. Unplugged the quick connect terminals (3) from the old switch and plugged them onto the new switch. one of the terminals had gotten quite hot and darkened the insulation so it was replaced with one that was supplied with the switch. that was a cut, strip, crimp process. Placed the new switch into the panel and snapped into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from CAMBRIDGE, MN
- Parts Used:
- WP33001762, W10169313
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Will not start all lights on,makes a ping sound on the control panel when you push the start button
Replaced thermal fuse and replaced door switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from pleasant valley, NY
- Parts Used:
- W10169313
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
door switch broke
remove bottom section under door 2 screws remove door 2 screws remove switch by squeezing tabs install 2 new female ends on wires supplied with switch . put switch back in plug in wires .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Fernley, NV
- Parts Used:
- WP338906
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Dryer got hot then heat would shut off
Sensor is in the front lower left. Gas off, electicity off. Removed two screws for the filter, pry/lifted the top up and taped it too the overhead cabinet, removed two screws inside top of front panel, lifted pandel with door closed staight off. Two screws to remove the flame sensor braket. unplug the old sensor install the new one and reverse everything. With others suggestions I purchased temperature switches etc. but the radiant flame sensor was the problem. I now have some spare switches for future. Excellent company and very quick service. Oh, Sears wanted 200.00 just for the service call, I live rural.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- claude from laguna niguel, CA
- Parts Used:
- 306436
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing, probably broken female latch part
Press in the new female latch part with thumbs. Took about two seconds!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- karl from monroe, GA
- Parts Used:
- 306436
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer would not stay closed.
I used a flat screw driver to pop out the old female portion and snapped in the new one. Dryer stays shut. That's it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Fairfield, CA
- Parts Used:
- MAL9000AXX
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Conversion from natural gas to liquid propane
By following the directions included with the kit it was fairly clear. The diagrams of the control valve was helpful. It would have helped to tell which screws to remove to access the valve and where the screw was that retained the burner assembly.
Was this instruction helpful to you?
Thank you for voting!
not drying all the way, not getting hot enough
loosened two screws on back of top,lifted top away from front panel.it just lifts off front corners,removed two screws at top corners.lift front panel up and out,this panel supports dryer tub,remove slowly,unplug door switch parts are located left side bottom two screws holding in had to have wife hold drum up to put front panel on
Was this instruction helpful to you?
Thank you for voting!