GCWM1069CD7 LG Washer Dryer Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Omnitech from Warrenville, IL
- Parts Used:
- AGM73610701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door would not close
There is a magnet at the bottom of the door which allows the door to be held ajar when the washer is not in use to allow the tub and gaskets to dry. A tab on the plastic housing which retains the magnet broke which allowed the housing to pull free of the door and stick itself to the machine preventing the door to close. Easy fix to replace the magnet was $18. Instructions were included in the box. Part number on the drawing was A165. PS3618292 Magnetic Door Plunger
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from STOWE, VT
- Parts Used:
- 4738ER1002A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
leaking tub-to-pump drain hose
Pull washer away from wall. Unplug cord and remove drain hose from receptacle. Remove 4 screws holding panel to rear of washer. Squeeze and slide back hose clamps on each end of drain hose and loosen center clamp with screwdriver. Remove old hose. Reinstall new hose in reverse order using existing clamps. Re-install back panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from AUBURN, CA
- Parts Used:
- AGM73610701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plunger fell out broken tab.
Just aligned and pushed in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from ALLEN, TX
- Parts Used:
- AGM73610701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Tab broke on the magnetic door plunger and wouldn't stay in
Pulled out the old plunger and inserted new one. Just have to make sure the tabs align with the slots.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from FLORENCE, MA
- Parts Used:
- 4866ER0007A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Lower Balance Weight Broken Concrete Internals
The web interface is nice, however in this situation it references the wrong part which was not known until the item arrived. Customer Service handled return, however I had to call LG directly to confirm correct part number (LG p/n 4866ER0004A = p/n PS3524040) but this was only after LG also gave wrong p/n. When replacement part arrived the internal concrete had a crack in it. The part is basically a plastic shell that is filled with concrete. However the opening (about 1 x 4) is left open and with the concrete having a crack in it the piece will vibrate together and continue to break down over time (which is what happened to the original one) Before installing I chose to fill opening with epoxy and a plastic layer, then covered with electrical tape to seal it in. I feel this item is poorly designed from LG. Additionally this item was poorly packaged by PS when shipping which caused the damage (it weights about 15 lbs and was allowed to float around in a large over-sized box filled with large air pillows). I have photos but no way to upload here.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SHIRLEY from HARTFORD CITY, IN
- Parts Used:
- AGM73610701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Magnetic Door Plunger would stay on washer and not stay in door.
Use just your finger to push it into place. VERY EASY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from BOTHELL, WA
- Parts Used:
- AEG33121501
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
TE error. Replaced heater / thermistor assembly.
removed top and front. heater is at the base of the tub. the nut compresses the rubber seal and may take some wiggling to remove the old one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne from MONROE, NY
- Parts Used:
- AGM73610701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Magnetic door plunger broke off, then got stuck inside the door and couldn't be removed for replacement.
I used another magnet to pull the old plunger out of the door and replaced it with the new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ritchie from HOUMA, LA
- Parts Used:
- 4036ER4001B
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
Making noise on the spin cycle
Disassembled washer, replaced bearings, seals and gasket. Watched instructional video to familiarize myself with the repair. Followed all steps as recommended, repair was straight forward without any surprises. Hardest part was removing the drum from the machine, somewhat heavy. Disassembled and replaced all bearings, seals, spider and gasket. Reinstalled in reverse order. Note: Upon tear down, I found the seal was pushed out, causing the bearing failure. I also found that the seal was installed incorrectly from LG. They have the seal lip facing the bearings, should be facing the water. This repair seems to be difficult, but was fairly self explanatory. All plug ins are color coded, all hoses are accessible with little effort. If you have basic skills you should be able to handle this repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from IOWA PARK, TX
- Parts Used:
- AGM73610701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door plunger had a broken tooth and would not stay in place.
Just put in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from SMITHVILLE, TX
- Parts Used:
- AGM73610701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One Plunger latch broken off.
Line up the plunger with the existing slots in the door and push in.
NOTE: When testing it was evident that the magnet was not as strong as the original one. I would rate as one step up from useless.
NOTE: When testing it was evident that the magnet was not as strong as the original one. I would rate as one step up from useless.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois from ARIZONA CITY, AZ
- Parts Used:
- AGM73610701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the magnetic door plunger fell on the floor,
the magnetic door plunger fell on the floor, would not stay in place and did not hold the door closed. Received a new on, put it in place. works just like it is supposed to. took all of 2 seconds. great service from
Partselect. got the new part in less than a week.
Thank you
Partselect. got the new part in less than a week.
Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria D. from MEMPHIS, TN
- Parts Used:
- AGM73610701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken retainer
pops right into hole
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Memo from LA MIRADA, CA
- Parts Used:
- 4861ER2001D, 2W20017E
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Washer was leaking.
After watching the video for installation of the bellow, I followed the suggested repair method and was able to repair my washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jo Ann from WYLIE, TX
- Parts Used:
- AGM73610701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plunger/magnet capsule fell out of door recepticale because plastic locking tab broke off
Simply inserted new plunger/magnet back into door with thumb&finger until you hear the little locking tabs click. No tools required.
Was this instruction helpful to you?
Thank you for voting!