41372 (ABWESEU) LG Washer Dryer Combo - Instructions

During my troubleshooting, I removed the bottom to access the drain pump. I had to cut some wire ties so that I could make removing the wires easier. After checking the pump and putting everything back together, I determined that the pump itself was bad. Pump impeller should not rotate freely! After receiving new part, I installed it relatively easy. I didn't have to remove the bottom since there was enough room through the access hole. Just make sure to make where wires go before removing old part.

It was so easy. i searched my model it brought up this site and the most common problem popped up without my even asking and recommended the part. i got it one week later and it was so simple to fix. a repair man wanted three times the part price to come to my home twice and would have had to wait longer. you guys were very helpful

1. Remove spring-loaded clamp assembly. 2. Partially pull out the large rubber gasket near the lock switch assembly to gain access to the lock switch assembly. 3. Unscrew two screws holding the lock switch assembly. Carefully separate the connector from the lock screw assembly and replace it with the new part. Reinstall in reverse sequence. Ensure that the electrical connector is fully seated unto the lock switch assembly and the connector latch is fully set against the lock switch body. Also make sure that the large rubber seal is fully seated around the door opening to prevent water leak. Restarted the washer and everything worked as before.

The machine was making a grinding noise instead of draining. I spoke with the LG rep on the 800 line and was told to call a repair man. The Parts select diagram helped me to identify the part I needed. It was clear enough that I was confident it was the right one. Three days and six screws later the machine was working fine.

new pump was a little different ,but mounted properly. Tipped washer on its side, changed pump by working trough bottom and back access. It went pretty smoothly, works fine.

I watched a video of how to replace the pump and it showed taking the top and front off to get to it. I actually found this could be done by removing the back panel from the washer. There were two hose clamps you have to squeeze and slide up and two wires going to the pump. There are three screws holding the pump that need to be removed from the front of the washer. Once these are removed all you have to do is push a tab down and the motor slide right out. The pump assembly can also be reached from the bottom of the washer.

Turn off hot water supply and activate a cycle on the washer momentarily, with hot water selected on front panel options to relieve hose pressure. Slide washer out to gain access to rear of unit. Unplug washer from AC source. Using pliers, remove washer supply hose from washer-side of the line (water may drain from hose) Remove single Phillips screw at bottom of each nylon lid holder at rear. Using a plastic putty knife, place between front panel and top lid to loosen lid and slide to rear. Remove lid and store aside. Hot and cold inlet valves sit side-by-side at top rear of the unit. Disconnect connector from valve by pulling gently away from valve plug prongs and place to the side. Using pliers, compress hose clamp and move to lower section of hose. Carefully rotate hose back and forth to remove from assembly. Inlet valve is held to washer body rear with 3 small Phillips screws. Remove first 2 and then while holding inlet valve body, remove final screw to free inlet valve assembly. Replace with new assembly by reversing these steps.Make certain when supply hose is reconnected, it is firmly tightened but DO NOT over tighten. Test washer by running a cycle to ensure there are no leaks.

Removed the old bellows (2 squeeze hose clamps and one screw adjustable hose clamp) slid on the new one and it was done!

The pump is apparently used for more than one washer, and the R&R instructions may be significantly different. I found a youtube video for my exact washer.

Removed the top, the front, got to the pump, removed it and replace it with the new one.

Found the part of Part Select by describing the problem. used a Utube video and step by step we were able to take apart, replace and put back everything with just a screw driver - I saved so much money!

Found great Youtube video, followed step by step. Only difficult part was getting the tub gasket clamp back on. But all in all pretty easy. If tub won't drain and weird noise coming from pump do not hesitate to do it yourself and save some coin!

Did the repair entirely from the back.- 4 screws back cover comes off. Once you see the Bellows it is obvious what needs to come off and there are other videos on the net showing this. The main things I did differently were 1) Leaned the washer forward and placed 3 2x4 blocks of wood under each back leg. This allowed me to reach under the washer with one hand, and through the back with the other. You need both hands in there ! 2) Uninstalling is easy with just pliers. But on the way back in, I used a pair of Locking Pliers to keep the circular clamp squeezed as much as possible. That seemed the only way to get the bellows back in. Another option would be to switch to screw on Pipe clamps instead of the spring clamps.

Hardest part was getting the correct part. Due to some glitch somewhere there was a mix up in the database for the correct pump number. This unit has two pumps mounted to the same housing. One is a recirculating pump and one is discharge pump. I ordered the discharge pump and kept receiving the recirculating pump. Discharge pump is LG PART#4681EA2001T and recirculating pump is LG PART #4681EA2002H Once in hand the install went fairly smoothly. Removed top - two screws on back of unit. Removed control panel with one screw on upper right inside corner, associated plugs and snap clips. Removed soap tray and drained water through filter tube. Removed screws in front of filter. Using Vise grips stretched spring from around front seal. Removed screws holding front of washer to top frame (2?)[accessed after soap tray removal]. Pump assembly located in bottom left, removed associated hoses, Marked wired colors on pump housings and removed. Removed assembly. Unscrewed pump, installed new pump and reversed procedure to reassemble. Struggled mostly with replacing spring around front seal. Stretch it as far apart as you can as you "roll" the spring in and then massage the seal to get the spring into correct position. Definitely a doable repair. Good Luck.

After checking for blockage on the drain hose and checking on any blockage on the bottom left corner filter and not finding anything i decided to open the machine. Everything suggested a broken drain pump
ITEM
PS3579318 Drain Pump and Motor Assembly which is located on the bottom left corner also and it attaches to the bottom left corner filter. And voila! The machine did not work! Now started throwing a FE code and it would not fill up. Well, the new pump was stuck! All i had to do was to stick my fingers in the bottom left corner filter orifice and move the fan like devices that make the new drain pump work, that did it! Be careful not to do it while the machine is pluged in, those plastic blades may hurt your fingers. To reach the drain pump you have to take the top, control board and front (door and gasket) of the machine off, about one hour labor.