41372 (ABWEPEU) LG Washer Dryer Combo - Instructions

Unplug Washing machine first. Then remove 2 screws at the back of the top cover. Slide the top cover back then lift and remove. Unplug electrical connector @ inlet valve and remove water lines 1 going in and 1 out of valve. Remove 2 screws holding assembly in place then install new valve assembly and all other components in reverse order.

pulled off top of washer to get at the inlet valve disconnect two hoses take two screws out and then you put it back together the way you took apart and your done

Our washer and dryer was stacked, and had to remove the dryer to access top of washer. This took 2 people and was not difficult due to the 168 lb weight of the dryer. Turned of water, pulled washer away from wall and disconnected the supply hoses. Removed the 2 screws holding the top, slipped it back and removed. Removed the 2 screws holding the inlet valve assembly, unplugged the wiring harness from the 3 solenoids, disconnected the 3 hoses from the hose bibs on the valves. Mounted new valve assembly, connected hoses making sure that clamps did not touch any other hoses, reconnected wiring harness, turned on water to check for any leaks, put top back on and tried washer out. Changing the valve assembly took a total of 15 minutes. Really simple. The You tube video very helpful in determining how to do the job.

First I turned off the hot and cold water supply and removed the water lines from the back of the machine. I then unscrewed the 2 phillips head screws on the back of the washer for the cover. I slid the cover back and lifted it off the machine. Next, I unscrewed the mounting screws from each inlet valve assemble located on the back of the machine by the hose connections. I used pliers to pull the hose clamps back from the inlet valve, 1 at a time, then reconnected each hose and clamp on the new inlet valve. Once each hose was connected to the new inlet valve, I discarded the old inlet valves. I then re-attached each inlet valve. I placed the cover back on the machine and secured with the 2 screws, re-attached the water supply hoses to the hot and cold side and turned the hot and cold water supply back on. Everything successful, no leaks, and washing laundry again..........leak free!

We drained the water from the washer via the tiny hose/filter located at the lower left corner of the washing machine. The unit was then pulled away from the wall, unplugged and the hoses disconnected. At this time, we used the wet dry vacuum to suction the water that remained in the drain hose. We tilted the washing machine back until the front of the unit was 18 inches or so off the floor. We used the foot stool to hold the washer up in the air so that we could work on the pump. Replacing the pump was as easy as removing a few screws, unplugging the electrical connections and removing the faulty pump assembly from the plastic housing. (Be sure to mark what connector goes in what terminal). Re-assemble. Re-connect. You are ready to go. It took more time to ready the washer than it did to replace the part.

UNPLUG WASHER.Unscrew 4 screws holding silver plate at back of unit. Remove plate to expose inside of unit. Locate drain hose at bottom of washer tub. Hose connects at front drain, bottom of tub, and at rear at the pressure sensor. Front and rear simply slide clamps down by grasping clamp tabs and sliding clamp off connection point. Disconnect from tub bottom by loosening main clamp with Phillips screwdriver and pulling downward. Have a towel handy as there will be water in the hose, and it will pour out when removing it from the unit. Installation is the reverse of removal. ATTACH THE HOSE ASSEMBLY TO THE DRUM FIRST, THEN FRONT, THEN LASTLY REAR. This order is the easiest way, otherwise you will spend extra minutes trying to get the tub connection to seat properly. Plug it back in (duh), then you're good to go for another 4 years or so until another hole wears in the hose. I have performed this repair on 3 different units, with 4 years being the average lifespan of this part.

ordered part from Part Select and it was here very quickly,but the part came damaged (not the fault of Part Select). I ordered another one and PartSelect had it here the next day. I watched the video on how to replace it and it was very helpfull.The particular part I replaced (pump motor) does not seem very durable. I will buy an American made washer the next time I need one. I will use Partselect in the future and recomend it to others.

I received the part needed within a few days from ordering. I immediately removed the leaking part with the new part. It was a very simple install, and my washer is now leak free. If you think you cannot do these simple changes, think again, it's much easier then you may think. Remove the top cover of your washer machine by taking off the two screws in the back. Remove the hose clamp with a pair of pliers and pull off from the intake valve, of course make sure your water valve is shut off before starting. Remove the two prong clip. Using your pliers, disconnect the main hot water hose. Use a Phillips screwdriver to remove the two screws that holds the valve in place. Remove and discard it and replace with the new valve. Follow the steps and your done, it's that easy....TC

removed dryer which was stacked on top of dryer. opened washer top by removing screws from plastic hold down parts on rear. replaced valves with new valves you all sent me. reassembled and restacked dryer on washer

I took the back panel off the washer and located where the leak was coming from. It was obviously coming from around where the cold water hose connects. Checked washers in hoses and they were good. Noticed a small drip on the valve assembly that the hose connects too. Took off small panel where the hose connections are mounted....disconnected all 3 black water hoses that connect to it (squeeze metal clamps with pliers and slide hoses off. and numbered them with permanent marker so I wouldn't get my lines crossed later), removed the quick disconnect electrical lines.... removed part and googled the parts diagram on this site.....identified the part in the pic and ordered....it was here in less than 48 hrs with the basic shipping (which stated 3-5 days:)....reassembled the same way I took it apart. I'm prud of myself, it was pretty easy and I'm sure it saved me a lot of money!:)l

Took off the old one and put the other one on. The only difficulty was that my husband has big hands and had a hard time getting to one end.

Removed the old bellows (2 squeeze hose clamps and one screw adjustable hose clamp) slid on the new one and it was done!

new pump was a little different ,but mounted properly. Tipped washer on its side, changed pump by working trough bottom and back access. It went pretty smoothly, works fine.

During my troubleshooting, I removed the bottom to access the drain pump. I had to cut some wire ties so that I could make removing the wires easier. After checking the pump and putting everything back together, I determined that the pump itself was bad. Pump impeller should not rotate freely! After receiving new part, I installed it relatively easy. I didn't have to remove the bottom since there was enough room through the access hole. Just make sure to make where wires go before removing old part.

1. Remove spring-loaded clamp assembly. 2. Partially pull out the large rubber gasket near the lock switch assembly to gain access to the lock switch assembly. 3. Unscrew two screws holding the lock switch assembly. Carefully separate the connector from the lock screw assembly and replace it with the new part. Reinstall in reverse sequence. Ensure that the electrical connector is fully seated unto the lock switch assembly and the connector latch is fully set against the lock switch body. Also make sure that the large rubber seal is fully seated around the door opening to prevent water leak. Restarted the washer and everything worked as before.