Models > 11080754003 > Instructions

11080754003 Kenmore Washer Dryer Combo - Instructions

Jump to:

All Instructions for the 11080754003
121 - 135 of 768
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Kelly from AMARILLO, TX
Parts Used:
80040
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
Agitator cogs all broken
Removed Softner dispenser and cap. With a 3/8" socket wrench and extension And 7/16" socket I took out the screw holding the agitator and removed top section of agitator. Turned upside down and removed the rubber grommet that holds the cogs in place. Replaced cogs and reinstalled grommet. Aligned top part of agitator with 2 tabs and put back in place and secured with 7/16" screw. Replaced cap And dispenser. Good to go. Works perfectly. Very easy repair.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Chris from Kernersville, NC
Parts Used:
80040
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
Top half of agitator would not agitate.
Removed top cap of agitator and pulled out the inner cap. Spread a pair of needle nose pliers and placed them in square holes on each side of nylon fitting. Unscrewed nylon fitting and removed top half of agitator. Replaced directional cogs/dog ears and put agitater back together. Works like new. Easy fix.

PS Received parts in 72 hours. $10.00 bucks and never left the house.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
randy from overton, TX
Parts Used:
285751
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
top wont agitate
removed top of agitator, used an extenison with a 7/16 socket, removed 1 screw, pulled out cam and only replaced the dog ears. put back together and now it WORKS LIKE NEW. (knock on wood)
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Todd from Milwaukee, WI
Parts Used:
80040
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set
Replaced the dog ears.
It was easy, take off the cap, then loosen the nut. Take it apart, change the dog ears, put back together. It was done.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Manchester, CT
Parts Used:
388253A
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
washing machine will agitate but not spin
I removed the cabinet and agitator, layed the machine on it's back, removed the pump, motor and gearcase. I found a way to prop the gearcase up so it rested level, removed the cover, drained the old oil. I removed all internal parts, disassembled them and cleaned them. I reassembled the gearcase using the new uetral drain assembly, and replaced the oil. I made sure the brake assembly was pushed into position and then put the gearcase, motor and pump back in. I sttod the machine up, put the cabinet back on and tested the machine. It still did not spin, so it wasn't the coupler, clutch or nuetral drain assembly.
14 of 38 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Frans from N ARLINGTON, NJ
Parts Used:
349241T
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Dryer was making a loud sound
I follow the instructions from the video you guys show the only issue is putting back the tensioner in place but my brother leaves next door and help me.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Charles from ERIE, PA
Parts Used:
349241T
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
Noisy while in use.
Turn off Gas, unplug electric cord, remove rear cover, remove two screws holding the lint trap to the top, raise top flip[ping to the back supporting it not to damage wiring, remove bottom front cover, remove door springs, remove front cover, disengage belt tensioner, remove drum. unclip right side roller and remove, unbolt left wheel mount from the rear and the bracket in the front, remove clips or cut off (new ones come with new clips). clean the wheel shafts, light sanding if needed, apply light coat of lithium grease. replace wheels and reassemble dryer in the reverse order from disassemble. roll drum by hand after front back on to ensure it rolls without catching. Finish and test.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Patrick from RUSSIAVILLE, IN
Parts Used:
285805
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
water would not shut off
Shut off both water valves and used a cup to catch water from hoses. Removed top control panel that's held on with 2 phillips screws. Remove top screws on the back to gain access. Was able to access the valve by pulling slightly out on the top corner.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ross from Plano, TX
Parts Used:
285805
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
noisy water mixing valve
Simple repair. Unplugged power cord, turned off water spigots. Removed the two screws under the control panel and rotated it up and back out of the way. Popped the two retaining clips (that's much easier now that I know to simply stick a large screwdriver straight down vertically into the front portion of the clip and lean the screwdriver back, rather than try to pry the clip out by levering under it against the washer top) holding the main body panel to the front of the washer and tilted it forward but not all the way off.

That allowed plenty of room to get at the back panel where the valve assembly is. There is some sort of plastic tray over the top of the valves that's kinda in the way so I popped it out by squeezing its plastic retaining barb with needle nose pliers and forcing it back thru the metal panel. Two screws hold the valve assembly on, and of course the water supply hoses are on one side and the fill hoses on the other. Removed and placed them on the new valve in order

The replacement part comes with a mounting plate and is not an exact duplicate. I screwed the assembly to the plate, but the holes in the plate don't line up perfectly enough to allow a second screw to be used. I could have drilled in a new one if I was willing to move the washer even farther out but a single screw holds it plenty well enough for me. Be sure to attach the correct electrical connectors and water lines to the new valves.

Reassemble in reverse order BUT TAKE CARE NOT TO PINCH THE CLEAR PLASTIC TUBE that runs from the water level switch down behind the control panel when you rotate the control panel back into position. I watched my washer fill almost to overflowing before realizing something was wrong. After 2-3 unsuccessful examinations I finally realized the tube was caught between two panels of metal and the controls were not recieving the "I'm full" signal from the wash tub. That would have been a mess if I hadn't watched a wash cycle to double-check my work.

My washer sounds brand new and fills faster. $30 shipped and an hour of work.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from New London, CT
Parts Used:
285751
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Socket set
As the washer was trying to move the agitator back and forth to wash the clothes it kept slipping and making a grinding noise and the agitator wouldn't move much at all.
I removed the top cap of the agitator which is actually the fabric softener dispenser.It comes off by hand.Under that was some type of a cap or a seal like piece of plastic.Also removed by hand.Under that I saw a 9/16 bolt head.I took that out with a socket set and a couple of extentions.Now I was able to remove the cup shapped part called the AGITATOR CAM ASSEMBLY. In this part are three comma shapped pieces of plastic.Sorta looked just like a big cashew nut.On these pieces there are little teeth which when working properly will swing out just a bit and lock into the agitator itself and this is what makes it move back and forth(or agitate). Well the teeth on mine were rounded off and would not grab the agitator.So I go to this stores web site by doing a GOOGLE search for my machines model number and this GREAT web site had an exploded view of my machine showing the exact parts by name and number that I needed.Great price ,supper fast delivery.Really I had these parts within 5 days of placing the order.I put them in and it went back together just as easy as it came apart.I called it a bit difficult because I had no idea how to take apart a washing machine and I didn't know what I was looking for when I got in there.I got lucky.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Keith from Mount Vernon, WA
Parts Used:
WPW10072840, 80040
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set, Wrench set
Timing tabs securing the agitator center
There are 4 tabs that come from the main agitator body through the center & lock into the centerpiece that holds the directional cogs. They have a tab similar to a cable tie that can only be put on once. They need to be clipped before it will dissassemble & reassembly is difficult because they need to be timed to reattach the round center cog plate. Maybe cut off 2 of them & taper the other 2 them for easier reassembly.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
kenneth from franklin, NC
Parts Used:
285805
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
Would not stop filling, overflowed.
Stopped by a friend who is an appliance repair person. He walked me through the Roper repair.
Removed the two screws, pulled the control panel up and back, disconnected the two wires. Sprung the two clips with a large screwdriver. That gave me the room I needed to do the repair. The hardest part was lining up the cover to go back on level. Part worked perfect, everyone was happy.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
joseph from san antonio, TX
Parts Used:
80040
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set
the top section of the agitator would not turn
First I came to this web site and discovered some directions from other customers. I then followed those directions to disassemble the agitator. I removed the softener cup by pulling up on the blue plastic retention ring. I then used a flat head screwdriver to remove the plastic cap by placing the screwdriver into the slot on the side and prying it off. Next I used a 3/8 socket and extension to remove the bolt which holds the agitator to the shaft. After the bolt was removed I pulled up on the agitator and removed it from the washing machine. To remove the upper section of the agitator, I placed it on the ground and holding the base with my feet, I pulled on the upper section. I then removed the dog ears, verifyed the problem and ordered the parts (dog ears). The parts arrived in less time than promised, were installed in about 5 minutes and I was back to doing laundry. When you reassemble the agitator, turn it upside down to install the dog ears so they do not fall out.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Roger from St. Albans, WV
Parts Used:
80040
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Top part of agitator not working
I used a nut driver to remove the screw that held the to part of the agitator onto the bottom part. I then took out the worn out directional cogs and replaced them with new ones and re-assembled the agitator and was back in business. The agitator now works the way it should. Easy fix. The only negative part of this experience was that the shipping was twice as expensive as what the parts cost. Very fast shipping from PARTS SELECT .
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sam from Sharon, TN
Parts Used:
285664
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
hose split
Pulled washer out from wall removed clamp and old drain hose addnew hose replaced clamp put washer back in plact connected drain to outlet simple operation
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 11080754003
121 - 135 of 768