11098752798 Kenmore Washer Dryer Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- james from Fredericksburg, VA
- Parts Used:
- 349241T
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
one of my rollers fell to pieces
just like the guy in the video. It was easy to folow his instructions, and the best thing of all i could stop the video if I had a question and then resume!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dianne from WALES, MI
- Parts Used:
- 80040
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Washer not agitating
Washer was not agitating. My husband did not have a clue what to look for, but he took it apart and noticed two of the four directional cogs were stripped. Did an internet search and found the part on your website and thought we would give it a try since the part/shipping was under $20. The parts came in three days and my washer lives on. Was ready to get a new one since it is 18 years old, but I will not wait. Excellent website with all instructions and parts breakdown of the washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from INDEPENDENCE, KS
- Parts Used:
- W10828351
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
internal dryer filter mesh torn
replaced internal dryer filter housing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from AMARILLO, TX
- Parts Used:
- 80040
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitator cogs all broken
Removed Softner dispenser and cap. With a 3/8" socket wrench and extension And 7/16" socket I took out the screw holding the agitator and removed top section of agitator. Turned upside down and removed the rubber grommet that holds the cogs in place. Replaced cogs and reinstalled grommet. Aligned top part of agitator with 2 tabs and put back in place and secured with 7/16" screw. Replaced cap And dispenser. Good to go. Works perfectly. Very easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Kernersville, NC
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Top half of agitator would not agitate.
Removed top cap of agitator and pulled out the inner cap. Spread a pair of needle nose pliers and placed them in square holes on each side of nylon fitting. Unscrewed nylon fitting and removed top half of agitator. Replaced directional cogs/dog ears and put agitater back together. Works like new. Easy fix.
PS Received parts in 72 hours. $10.00 bucks and never left the house.
PS Received parts in 72 hours. $10.00 bucks and never left the house.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Geri from COUNTRYSIDE, IL
- Parts Used:
- W11050897
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
was not heating
remove back of dryer and install part same as old part was installed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from ALBUQUERQUE, NM
- Parts Used:
- 80040
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitator not moving
Half inch extension. Removed plastic set piece. Remove agitator cap. Remove ring remove worn cogs. Replaced new cogs Replace lock ring, back together. 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- randy from overton, TX
- Parts Used:
- 285751
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
top wont agitate
removed top of agitator, used an extenison with a 7/16 socket, removed 1 screw, pulled out cam and only replaced the dog ears. put back together and now it WORKS LIKE NEW. (knock on wood)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from Milwaukee, WI
- Parts Used:
- 80040
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Replaced the dog ears.
It was easy, take off the cap, then loosen the nut. Take it apart, change the dog ears, put back together. It was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frans from N ARLINGTON, NJ
- Parts Used:
- 349241T
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Dryer was making a loud sound
I follow the instructions from the video you guys show the only issue is putting back the tensioner in place but my brother leaves next door and help me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from ERIE, PA
- Parts Used:
- 349241T
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Noisy while in use.
Turn off Gas, unplug electric cord, remove rear cover, remove two screws holding the lint trap to the top, raise top flip[ping to the back supporting it not to damage wiring, remove bottom front cover, remove door springs, remove front cover, disengage belt tensioner, remove drum. unclip right side roller and remove, unbolt left wheel mount from the rear and the bracket in the front, remove clips or cut off (new ones come with new clips). clean the wheel shafts, light sanding if needed, apply light coat of lithium grease. replace wheels and reassemble dryer in the reverse order from disassemble. roll drum by hand after front back on to ensure it rolls without catching. Finish and test.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Mount Vernon, WA
- Parts Used:
- WPW10072840, 80040
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench set
Timing tabs securing the agitator center
There are 4 tabs that come from the main agitator body through the center & lock into the centerpiece that holds the directional cogs. They have a tab similar to a cable tie that can only be put on once. They need to be clipped before it will dissassemble & reassembly is difficult because they need to be timed to reattach the round center cog plate. Maybe cut off 2 of them & taper the other 2 them for easier reassembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from RUSSIAVILLE, IN
- Parts Used:
- 285805
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
water would not shut off
Shut off both water valves and used a cup to catch water from hoses. Removed top control panel that's held on with 2 phillips screws. Remove top screws on the back to gain access. Was able to access the valve by pulling slightly out on the top corner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ross from Plano, TX
- Parts Used:
- 285805
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
noisy water mixing valve
Simple repair. Unplugged power cord, turned off water spigots. Removed the two screws under the control panel and rotated it up and back out of the way. Popped the two retaining clips (that's much easier now that I know to simply stick a large screwdriver straight down vertically into the front portion of the clip and lean the screwdriver back, rather than try to pry the clip out by levering under it against the washer top) holding the main body panel to the front of the washer and tilted it forward but not all the way off.
That allowed plenty of room to get at the back panel where the valve assembly is. There is some sort of plastic tray over the top of the valves that's kinda in the way so I popped it out by squeezing its plastic retaining barb with needle nose pliers and forcing it back thru the metal panel. Two screws hold the valve assembly on, and of course the water supply hoses are on one side and the fill hoses on the other. Removed and placed them on the new valve in order
The replacement part comes with a mounting plate and is not an exact duplicate. I screwed the assembly to the plate, but the holes in the plate don't line up perfectly enough to allow a second screw to be used. I could have drilled in a new one if I was willing to move the washer even farther out but a single screw holds it plenty well enough for me. Be sure to attach the correct electrical connectors and water lines to the new valves.
Reassemble in reverse order BUT TAKE CARE NOT TO PINCH THE CLEAR PLASTIC TUBE that runs from the water level switch down behind the control panel when you rotate the control panel back into position. I watched my washer fill almost to overflowing before realizing something was wrong. After 2-3 unsuccessful examinations I finally realized the tube was caught between two panels of metal and the controls were not recieving the "I'm full" signal from the wash tub. That would have been a mess if I hadn't watched a wash cycle to double-check my work.
My washer sounds brand new and fills faster. $30 shipped and an hour of work.
That allowed plenty of room to get at the back panel where the valve assembly is. There is some sort of plastic tray over the top of the valves that's kinda in the way so I popped it out by squeezing its plastic retaining barb with needle nose pliers and forcing it back thru the metal panel. Two screws hold the valve assembly on, and of course the water supply hoses are on one side and the fill hoses on the other. Removed and placed them on the new valve in order
The replacement part comes with a mounting plate and is not an exact duplicate. I screwed the assembly to the plate, but the holes in the plate don't line up perfectly enough to allow a second screw to be used. I could have drilled in a new one if I was willing to move the washer even farther out but a single screw holds it plenty well enough for me. Be sure to attach the correct electrical connectors and water lines to the new valves.
Reassemble in reverse order BUT TAKE CARE NOT TO PINCH THE CLEAR PLASTIC TUBE that runs from the water level switch down behind the control panel when you rotate the control panel back into position. I watched my washer fill almost to overflowing before realizing something was wrong. After 2-3 unsuccessful examinations I finally realized the tube was caught between two panels of metal and the controls were not recieving the "I'm full" signal from the wash tub. That would have been a mess if I hadn't watched a wash cycle to double-check my work.
My washer sounds brand new and fills faster. $30 shipped and an hour of work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from New London, CT
- Parts Used:
- 285751
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
As the washer was trying to move the agitator back and forth to wash the clothes it kept slipping and making a grinding noise and the agitator wouldn't move much at all.
I removed the top cap of the agitator which is actually the fabric softener dispenser.It comes off by hand.Under that was some type of a cap or a seal like piece of plastic.Also removed by hand.Under that I saw a 9/16 bolt head.I took that out with a socket set and a couple of extentions.Now I was able to remove the cup shapped part called the AGITATOR CAM ASSEMBLY. In this part are three comma shapped pieces of plastic.Sorta looked just like a big cashew nut.On these pieces there are little teeth which when working properly will swing out just a bit and lock into the agitator itself and this is what makes it move back and forth(or agitate). Well the teeth on mine were rounded off and would not grab the agitator.So I go to this stores web site by doing a GOOGLE search for my machines model number and this GREAT web site had an exploded view of my machine showing the exact parts by name and number that I needed.Great price ,supper fast delivery.Really I had these parts within 5 days of placing the order.I put them in and it went back together just as easy as it came apart.I called it a bit difficult because I had no idea how to take apart a washing machine and I didn't know what I was looking for when I got in there.I got lucky.
Was this instruction helpful to you?
Thank you for voting!