41797962702 Kenmore Washer Dryer Combo - Instructions

My washing machine stopped agitating and spinning and I couldn't afford a repair man...plus I wanted to exhaust any obvious problems first. One of the leveler feet had broken years ago. Since I luckily had determined via reading other posts that the agitator won't work if the cycle safety switch is not functioning right, I thought the safety switch might need to be changed but after careful thought, I decided to order a new levelling leg first because maybe the broken levelling leg was shaking the safety switch so it wasn't connecting right. Once I received the leg overnight, I flipped the washer on its side and had to drill out the old leg. It was a little tricky because of how it broke, but the drill worked. I flipped the washer back up, leveled it with the new foot, and the agitator was miraculously working again...just like new. I didn't need the safety switch. Thanks to partselect.com for having the details of my washer parts to study up on and get me the right part so quickly. I saved myself alot of money.

unplugged the dryer, discontected the sensor and unscrewed the bracket, replaced the new one and put the connectors back on, screwed the bracket back on and that was it. Very easy fix for a female who does not do much of these sort of repairs but learning.

I've always been a "do it yourselfer". If I can fix it, I save money. I took the dryer apart by lifting the top up like car hood. Then I removed the front panel. The front drum glide snapped into place easily where the other one had broken off. The felt strip that you sent was much shorter than the one on the dryer, so once I used the wire wheel to remove the old glue, I cut off the section of the felt that was bad and replaced it with the new felt. The turns much quieter and clothing doesnt get caught behind the drum anymore.

Happened to slam the lid by mistake and the washer started spinning. Recognized the lid lock was working haphazzardly. Also, there was a burning type odor coming from the switch. So I lifted the lid top and disconnected the switch from the lid by unscrewing 2 screws and 4 wires. When I received the new switch, I reinstalled it with 2 screws and reconnected the 4 wires.

I opened the top of the dryer to gain access to the outside of the drum. Then I removed the screws holding the old drum veins in using the electric drill with the nut driver attachment. Then I positioned the new veins in place on the inside of the drum and replaced the screws from the outside of the drum to hold the veins in place. Then I replaced the top and was ready to go.

This is the third repair that I have done using parts from parts select. the other two repairs involved replacing electrical parts. Specifically thermostatic controls or swicthes. I am very happy with the parts and the diagrams provided on your web site without wich I would have had to replace my dryer a long time ago.

This unit is a stackable washer&dryer,so first pull unit away from wall atleast 4 foot. Unplug power cord,then take10 dagree front panel off then the control panel off and unplug the 5 connetors if your unit has that many,then lay panel asside. Take dryer door off,makes it easier when putting it all back together. Now take front panel off and the dryer lent tube,now just take the 3 center phillips head screws out and slide drum out. Pull upward on what they call the shaft which held drum on. Now these are the parts you should order. Belt,grounding ball clip,grounding ball,drum support bearing,bearing bracket,and most important part is the shaft. The shaft is ur insurance for the whole job. Use a good grease like white lithium grease and coat the shaft end and the drum support bearing. The grease will cut down on friction for a while,and re assemble the way you took apart. Reminder grounding ball goes behind drum support bearing not in front. Good luck and please vaccum.

ordered part from parts select, it was the wrong part,( all my fault) they refunded part upon return and sent the new part, the return was easy and prompt, new part arrived, 15 minutes wife was washing and happy again, and we all know, happy wife happy life, thanks part select!!!

First I removed the two screws that hold the pump in place. I then pulled the pump out and replaced it with the new pump.

I pulled the old motor out of the bottom of the washer. After undoing the screws and taking off the belt. I threw the new one in and tightened everything up and put the belt back on and it worked great... Super easy to change a motor out and a lot cheaper than buying a new waher...

The best part was that it only took one day to ship to my house and I picked the cheapest shipping amount... I recommend this site..

0) Turned off breaker at panel and disconnected power cord from 240v wall outlet
1) Removed screws that hold electrical cover plate on back of dryer.
2) Lifted the top of dryer using putty knife on 2 top edges of lid. This lifts up like a cars hood.
3) Removed the screws that attach the power cord to the terminal block and disconnected power cord
4) Removed screws that attach terminal block to dryer
5) Removed melted terminals by prying out of terminal block. Note metal lip on terminal has to be lifted in order to slide connector out. Also unscrewed ground wire from terminal block to dryer.
6) Drew diagram of what color wires go to what terminals
7) Cut terminals off of wires and connected new terminals. Crimped closed and used butane solder torch to solder connection between terminal and wire
8) Reconnected terminals to terminal block by sliding in. **Note, had to file down the edges of the terminals using moto-tool to make it fit as they are connected together using break-away tabs that leave a large piece of metal connected not allowing to fit in terminal block
9) Reconnected terminal block to dryer and reconnected ground wire.
10) Reconnected power cord to terminal block with screws
11) Replaced cover over wiring terminal block
12) Reconnected power cored to 240ac wall outlet
13) Turned breaker back on

followed the instructions on a blog

i removed the front panel, then removed the old pump by taking off the clamps and disconnected the wiring. The new pump had to be reversed before connecting, but it was so easy.

White Westinghouse WDG547PB Dryer. Removed access panel (lower left front of dryer) by removing phillips head screw below access panel. Removed two phillips head screws holding bracket that holds coil in place. Removed coil, disconnected electrical connector. Connected electrical connector to new coil and set in place. Repeat for second coil. Reinstall bracket and access panel. Job complete. Dryer back in service with no problems.

I'm a 70 year old widow.. ordered the part which came in 2 days..(.very reasonably priced) My son came over and in no time had the old out and new in...works like a new machine... Thank you Part Select. A few months ago ordered a stove ignitor..it too came really fast... stove is good for another 15 years..LOL

Internet Search suggested that I check the Igniter, Sensor, thermal cutoff and Ignition Coils. down in the bottom of the Gas Dryer. With top cover off and front panel on, I put a mirror down in the bottom of the Dryer. I watched to see if the Igniter and the Sensor would turn on the Gas Valve. In the reflection of the Mirror, I could see a glow, but heard NO clicks. Repeated several times. Same Result. I suspected the Ignition Coils were faulty.

You suggested replacing BOTH. Parts arrived in 2 days. :-) Easy disassemble and reassemble with screwdriver. (Front Panel must be removed). While I was at it, I replaced the Drive Belt, too. It was 6 years old.
Everything worked fine.
After 6 years in a Garage, the Dryer was filled with Dust. Use the opportunity to Vacuum out the dust.