41799887990 Kenmore Washer Dryer Combo - Instructions

I pulled the old motor out of the bottom of the washer. After undoing the screws and taking off the belt. I threw the new one in and tightened everything up and put the belt back on and it worked great... Super easy to change a motor out and a lot cheaper than buying a new waher...

The best part was that it only took one day to ship to my house and I picked the cheapest shipping amount... I recommend this site..

White Westinghouse WDG547PB Dryer. Removed access panel (lower left front of dryer) by removing phillips head screw below access panel. Removed two phillips head screws holding bracket that holds coil in place. Removed coil, disconnected electrical connector. Connected electrical connector to new coil and set in place. Repeat for second coil. Reinstall bracket and access panel. Job complete. Dryer back in service with no problems.

followed the instructions on a blog

i removed the front panel, then removed the old pump by taking off the clamps and disconnected the wiring. The new pump had to be reversed before connecting, but it was so easy.

Lifted top
removed adgetator
removed tub top
removed inside tub
removed inside tub holder bracket
repaced seal
replaced,replaced.....

Removed dryer front, unscrewed 3 screws in center hub, replaced bearing assembly. Removed old basket seal with razor scraper, cleaned surface with mineral spirits, applied new basket seal. Replaced dryer front and project was done. Dryer has no more sqeaks.

Unplug dryer (gotta say it). Remove the two screws that hold in the lint catch. Remove top of dryer (two screws in back hold brackets, the front snaps on). remove two screws along the front edge to take front panel off the dryer (there are also clips). Unhook the two electrical connectors that control the door shut off. Once the front is off, remove the old glide and felt and install the new parts. Be sure not to step on the tube of contact cement, making it explode inside the bag. That sucked. Reassemble.

I'm a 70 year old widow.. ordered the part which came in 2 days..(.very reasonably priced) My son came over and in no time had the old out and new in...works like a new machine... Thank you Part Select. A few months ago ordered a stove ignitor..it too came really fast... stove is good for another 15 years..LOL

Make sure you order a new belt and a new drum glide with the rear drum bearing assembly. If your bearing is worn out, so are the belt and drum glide!

1) Use a flat screw driver or putty knife to release the blind clips that hold the front side of the top of the dryer cabinet down
2) Swing dryer top up and remove two screws that hold the face of the cabinet.
3) Unplug the wiring harness and remove the cabinet face.
4) Remove the 3 screws that hold the drum to the bearing assembly (accessed from inside the drum. This makes it easier to remove the drum as the bearing assembly can be difficult to remove before you see how it snaps together
5) Reach under the drum and take the belt off the motor pulley, then remove the drum
6) Remove the old bearing assembly from the socket (slide up then out)
7) Remove the two screws that hold the bearing socket to the dryer
8) Fasten the new socket to the dryer (you'll need help doing this unless you have REALLY long arms because you have to reach inside the driver and the back of the dryer at the same time)
9) Grease the socket with the supplied high temp grease
10) Bolt the new bearing assembly to the drum and put the new belt around the drum
11) Put the drum back in and snap the bearing socket in and down
12) Guide the new belt around the motor pulley & tensioner
13) Glue the new drum glide / felt piece to the front cabinet
14) Put the cabinet back together

First of all, the folks at Part Select have been terrific. I balled up my address and they were great in correcting my error and getting the parts promptly to me. They provide directions with the parts. And You Tube, is a wealth of information too. The process is to remove the drum and replace the nylon busihing that supports the drum at the back of the machine. Getting it out was no sweat. Getting the drum back in was a bit more challenging single handed. If I was going to make any suggestion it would be this is a good project for two sets of hands with the second set needed for about ten minutes. The You Tube video I watched said putting the front cover with the drum attached to the back of the unit would be the challenge and they were right. Otherwise, super easy and the results are it's back to "new" condition. Thanks again to Part Select!

I removed the top of the washer by removing two screws on the back. I located and bypassed the lid switch to make sure that wasn't the problem. The problem still existed so I removed the two screws that hold the front panel of the washer. Using a flashlight, I located the drive belt and immediately saw that it was out of position and had pieces missing. I cut and removed the old belt, placed the new belt on the tub pulley and slowly maneuvered it onto the motor drive wheel. I then squeezed the tensioner pulley so that the belt was seated. I turned the timer dial which started the washer and it immediately began pumping the water out of the tub. Problem solved!

After the new replacement part arrived, I took off the complete back panel (after unplugging the electrical and shutting off the hot & cold water supply). I disconnected both hot & cold water hoses, unscrewed the 2 screws holding the water valve, unplugged the 2 electrical wires for the water valve sending unit, unclamped the outlet water hose. Then I reversed order with new water valve. Put everthing back together in about 20 minutes overall. I did also replace the hot & cold water supply hoses with a better quality hose. Works like new! Thank you very much.

First I read the manual on how to replaced the dryer drum belt. Second I took off the front panel. This would involving taken all screws from the top of the dryer face and the front panel. Thirdly I removed the exhaust attachment. Then I saw that the belt broke. Really it looked torned apart. I believe too heavy of a load in dryer. I then installed the new belt and reversed everyhing I did to start. The dryer runs great. This is not that bad of a job. If you can do it yourself, why pay hunreds on a service man to do the job.

S/O Water , Removed front panel, removed screws from side panel water valve accessible. Removed screws that hold water valve, installed new valve reassembled washing machine.

removed the two 'lock down flanges' from the back of the machine, lifted the top from the front and slid it forward to access the valve. Removed the two electrical connections then the compression ring from the hose on the output side. Removed two screws holding the valve in place, then reversed the process.

I wish this valve was made of metal rather than plastic. I had to replace it because the threads were stripped. Here's the heads up. Make sure the fittings on your supply hoses are 'clean' or you'll mess up the plastic threads and not get a good seal.