41789980100 Kenmore Washer Dryer Combo - Instructions

First I have to say that the video on the Parts Select website was invaluable, it truly made the replacement a no brainer. The kit came with everything I need and was a great price.

Unplug the dryer, mine is a stackable so we had to remove the dry from the top of the washer. I then followed the instructions from the video. The only real difference was that my dryer is that is has dual direction tumbling, so there were 2 idler arms instead of one to move in order to un hook the belt. was pretty easy.

I only needed my husband's help a couple of times because 1. To get the dryer off of the washer. And 2. I didn’t have the reach to install the new bearing on the back of the drum.

Taking it apart was no problem other than having to remove solidified grease in order to remove bearing. Also I found it easier to remove belt by removing screws holding drum in place first. Putting it back together was more involved. Taping metal strip to back with scotch tape made putting in new bracket a breeze. Tipping dryer on its' back was the only way I could get the screw holes to line up when installing the drum. Removing the vent cover, and installing from the back, made re-installing the belt tensioner much easier.

FOLLOW THE VIDEO!! I was scared to even get into it until I watched the video. Made it easy for me and I have little to no mechanicl skill. Excellent video that made it super easy. Took me an hour as I was taking my time. Now I could probably do the same repair in 20 minutes.

I followed others instructions on this site to disassemble but felt confident since 2-3 years prior I had replaced the felt top/bottom guides around the drum and the drum belt. The video on this page is also helpful

1) Pop the top with a putty knife
2) Unscrew two screws that hold the front onto the dryer frame
3) Lift front from two clips at bottom of dryer
4) Release tension from belt (unscrew/remove rear access plate)
4) Lift drum up and forward out of dryer
5) Unscrew drum bearing 3x screws from inside of drum
5) Remove the drum bearing holder
6) Pre-thread the rear drum bearing!!! Very important. Thread by screwing a supplied screw slowly through the pre-drilled holes.
7) Attach drum bearing
8) Attach new rear holder/cup & ball bearing (ball bearing goes on outside of plastic cup)
9) Use lots of supplied grease, espeiclly helpful that it acts as a temporary glue holding the ball bearing in place
10) Reverse steps to assemble

I'm glad I bought the entire rear bearing kit as I found the bearing holder had completely worn through and partially melted the metal cup. The ball bearing was missing - gone!

Also found that the power cord had partially melted, so I replaced that from the hardware store. Scary.

Followed others directions and it went very well. I could not believe how much lint was packed in the bottom of the dryer! Need to clean this area out perhaps once a year.

Followed online video. All went smooth. Runs great!!!!!!!!!!!!!

I have a frigidaire dryer about 5 years old.

I first removed the top cover being careful to watch how the wires to the controls are connected. It is best to snap photos with your digital camera so you can remember how to reconnect the wires.

Pulling up on the drum, I lifted it out of the rear sleeve. Once out, you could easily see why it squealed. The metal bearing had groves on it where is made contact with the holder.

The difficult part of this was getting the 3 screws that hold the bearing to the drum off. The phillips screw head was easily marred if you don't have the proper screw driver bit. I think a better screw head would make the job easier.

After removal, the replacement was a snap. When everything was back together, the dryer sounded like new. The job took me about 2 hrs due to the hard part of removing the screws.

Excellent!!! The parts fit perfectly, but most of all was the video that went through the repair step-by-step.

A local repairman quoted $198 for parts and another $150 for labor. Got the parts here for less that $26!!!!

The only issue (very minor) was the video called for a phillips head screwdriver to remove the front panel, and our dryer needed a squarehead driver. (If I was younger, I would have been able to see the problem).

But, I highly recommend Partselect!!!!

The part arrived just in the nick of time as my wife and daughter had strung up rope all over the family room to dry clothes. My son helped me lower the dryer to floor level ( this is a stackable washer/dryer set) Removed the top and front of cabinet. Removed the belt and popped out the drum. Took this opportunity to clean the amazing amount of lint from the blower housing and discharge hose ( it is my opinion that the accumulation of lint and the subsequent rise in operating temperature is the main cause of this bearing failure) Removed and replaced the rear bearing and greased it. Reassembled the drum,installed the belt and reassembled the cabinet. the only tools used were a screwdriver and a nut driver....and of course a vacuum cleaner. The rebuild kit is very complete and is the only way to go. Thanks for your fast delivery time, one more clothes line in the family room and I wouldn't be able to watch T.V.

Followed video instructions that were emailed by you.

Taking apart cleaning putting back together I don't have any h-t lube so ill be doing it again. Thanks for the part ill be calling again!

We followed the video exactly. The video itself was simple and straight forward. Our model was a bit different than the video's example. The video's example had their spring action for the belt configured differently. When we finally figured out the difference, we were able to finish the job within minutes. The dryer now runs like new. We aren't mechanically inclined. That's why it took us so long. I still would recommend this company to anyone because it saved us time and money. The video really helps!

i took apart the dryer and then took out the drum from the inside and then put the new bearing in and put everything back in

First, used a putty knife to open the top of the dryer. Second, unscrewed the front panel and removed it by pulling up and out. The drum drops down slightly after doing this. Third, open the back grating and disconnect the belt from the motor and idle pulley. Fourth, Pull the drum (with belt) out through the front opening. Jerk up HARD on the back of the drum to disconnect it from the bearing seat. Fifth, replace bearing parts and seat according to diagram. I found it very difficult to unscrew the bearing axle from the drum. Had to hold down the drum and press hard to get screws to turn without stripping. Finally, put back together in reverse, don't forget to put A LOT of grease in your new bearing seat before reconnecting.

removed the drum out the front and replaced