41789980100 Kenmore Washer Dryer Combo - Instructions

I researched possible causes on line and watched a PartsSelect video on YouTube on how to test. I ended up misreading test results and ordered the High Limit Thermostat but subsequently realized problem was the Terminal Block. No problem, PartsSelect took back the Thermostat (I hadn't installed it) and shipped me the Terminal Block. My dryer was back up and running in less than 7 days from initial analysis to installation of Terminal Block. Instructions that came in confirmation email for installation were perfect and easy to follow. Total cost with new power cord from Home Depot was less than $50 vs a quoted service call of $175+ parts from local electrician.

Popped the tub cover off....replaced with new one.
Thank you so much for a speedy delivery.

Removed old belt. Installed new belt.

I followed the following instructions provided by the parts page and they were EXCELLENT! I had NO problems and was actually enjoyable to fix, thx. to these instructions listed below. Many thanks!!!! FIRST I REMOVED THE TOP PANEL HELD BY FOUR SCREWS AT REAR OF PANEL, PULLING THE PANEL FOWARD AND UP. THEN DISCONNECTED THE POWER AND WATER CONNECTIONS. THEN I REMOVED THE TWO SCREWS HOLDING THE FLOW VALVE TO THE WASHER REAR PANEL,PULLED THE VALVE FOWARD ,REMOVED THE TWO ELECTRIC CONNECTORS, PINCHED THE WATER CLAMP WITH PLIERS AND REMOVED THE WATER CONNECTION TO THE VALVE. THEN REPLACED WITH THE NEW VALVE FOLLOWED THE ABOVE STEPS IN REVERSE ORDER, FINISHING UP BY RE PLACING THE WATER CONNECTIONS AND POWER. THEN CHECKED FO PROPER REPLACENENT AND LEAKS BEFORE REPLACING TOP PANEL

Part came in, fast delivery. Took 10 minutes to install. Real easy works great.
Thanks PartSelect.

Popped the topped using a putty knife to free two clips in front. Remove two screws now accessible on the front inside panel. Remove two wires to door switch. Remove rear access door, two screws. Remove belt from tensioner in rear and remember or take picture of how it goes. Lift barrel slightly and pivot front panel out of the way. Lift barrel free from ball socket in rear. Lift out from front panel area. R & R kit and put back in reverse order.

After watching the video that explained and showed how to replace the bearing assembly, installation was a breeze. Great company to do business with. Ordered the part and had it in two days, and the dryer was working again asap. Thanks PartSelect
PS this dryer is 23 years old.

Lift washer lid by jerking the lid up and open. Remove front panel by removing 2 screws at front bottom and guiding tabs out of slots. Locate tabs on tub cover and gently pry loose with a flat blade screwdriver or putty knife. Remove tub cover and inspect seal area for damage or debris. Replace new tub cover on tub and align and fasten each tab. Ensure that lid is securely fastened to tub by pressing top of cover down and visually inspecting that each tab is engaged with tub hooks. Replace front panel. Use anti-seize grease when replacing the 2 front panel screws. Use a small amount of petroleum jelly on the top lid spring clips before closing washer top. (The last 2 tips will help any future opening of the washer.)

I love technology. First thing I did was google on "U-tube", "How to repair a squeaking dryer". Several videos out there so I just found the one I needed and watched. The repair itself went easy. A word of advice would be to be careful of sharp edges and to remember to unplug the machine prior to repair. While the drum is out, go ahead and get your shop vac and clean the inside of the unit out. Also, not only put grease on the new plastic holder, but put some on the shaft of the idler puller. I also used an awl to line up the holes on the front panel when re-installing the screws. One video I watched showed reaching in through the front to take the drum belt off the pulley, where another showed removing the inspection plate on the back. This made it much easier.

Removed the top of the dryer above the dryer door by pulling the pop out plastic holds. I then removed the dryer plug in at the top inside dryer that controls the start when dryer door is closed. I thenremoved the screws that are located at the back of the dryer tub where the bearing is located. I then replaced the support bearing. I just replaced every thing I took off in reverse.

This was for my Daughter's dryer. A helper really makes this quick and easy. First of all-UNPLUG the unit from the wall. I pried the top up with flat screwdriver. Laid the top back against wall. Removed the two wires from the door cut-off switch. Then removed the two screw attaching the front to the cabinet. Removed the small access panel on back of cabinet. Depressed the belt tensioner to release pressure on the leather drive belt. Went back to front, pushed the belt to the rear of cabinet, then lifted the back of drum to pop the bearing up and out of the plastic cup. I then tilted the drum forward and down and removed through front of cabinet. Reached inside the drum with Phillips screwdriver, removing the two screws to realease the bearing and BB bracket from back of drum. I attached the new bearing cup with BB to the back of cabinet, filling the cup with the high temp grease provided in the cup. Before installing the new bearing on the drum, I ran the new screws into and back out of the new bearing to cut the threads, making it easier to attach on the drum. I then put the drum back into the cabinet popping the bearing into the top of the plastic cup. Next I went to the back, put a bit of grease on the shaft that the tensioner bearing rides on. I re-set the belt on the tensioner, making sure the belt was back in the original position around the drum. I then re-attached the front cabinet centering the front of the drum on the felt. This felt supports the front of the drum. I manually gave the drum a few turns to make sure the drum was centered properly, and belt was mounted correctly. I then re-attached the two wires to the door switch. Slid the dryer into position, inserted the plug back into the outlet. Turmed it on, and now the dryer runs like new again. My Daughter is happy again. You will want to have a vac handy because it is unbelievable how much lint and dust are in the cabinet. I also took the filter bracket apart and cleaned it too.

There are really good instructions with photos on line - search squeeky dryer. I would add that it is easier if you mount the new bearing assembly on the drum before placing the drum back in the dryer cabinet. I guess this is obvious but was not stated in the referenced instructions. The round bearing slotts fairly easily into the plastic pillow block mounted on the back of the cabinet. Just make sure the small ball bearing remains in the center groove - lots of greese will help this.

Removed two screws that held top of washer in place. removed top of washer. Removed two screws that held water inlet alve in place. Removed clamp and outlet hose from old inlet valve.












































































Removed two screws hold wash machine cover in place. Removed cover. Unscrewed cold and hot water supply lines from old inlet valve. Removed two screws holding inlet valve in place. Removed clamp and hose from inlet outlet hose. Replaced inew inlet in reverse order.

I had trouble with the little piece on the back side of the dryer not lining up with the bearing housing. I also didn't see how the drum was gonna stay in place but finally realized the front cover lines it up. All in all it was awesome to get the part I needed so quickly and cheap, thanks a lot.

We had the rear drum bearing replaced about three years ago. The company that serviced it was quick to take our money for the diagnosis but took over a month (and a threat to call the better business bureau) to actually make the repair. This time I decided to do it my self as I had successfully replaced the the drum drive belt two years ago. The dissassembly was challenging but the repair it's self very easy. I opted to use nuts and bolts to attach the bearing assembly rather than the supplied screws as they did not want to tighten. Reassmbly was a bit of a challenge regarding the drum drive belt but I had the entire repair done in less than an hour.