41794872302 Kenmore Washer Dryer Combo - Instructions

From previous responses on this site. I just followed their lead. If I had not found these folks, and the responses, it would have been a nightmare. It looked like and I thought the dryer came apart from the back! But in reality it comes apart from the front!! Absolutely fantastic site and help. Fast shipping, I ordered on Wednesday before Labor Day, didn't expect the parts until the following Wednesday, but received the parts on Saturday morning, and had the dryer back running by Sunday AM. Never even ran out of clean clothes!!!!!

removed top and front panel on stackable dyer unit. 3 screws at back of the inside of the drum, and the drum was out. installed new bearing and belt and all was good.

I made my job difficult by removing the back panel, then the side, and finally discovered the front panel opens giving access to the washer. Using heavy pliers I removed the spring clamps and replaced the pump to washer hose and the other hose end to the tub. Turned on the washer no leak only to discover the drain hose had developed a leak. So I ordered the second hose. I was not sure how to release the plastic retaining clamps. Finally just yanked them loose, which worked. Ran the hose through the machine out the back into the drain pipe. I was able to reattach the retaining clamps put the spring clamp on the pump end of the hose. The difficult part was getting the back, sides and front of the washing machine together that took hours.

i left my washer on its back till my belt came in and when it did all i had to do is slip the front off and go at it. it was really fast. then i put the front back on screwed in two screws and hooked up hoses and started washing everything went smooth till i was about to wash wash-n-wear and was like where is my other houseshoe and i remember my dog was bugging me while fixing my washer and dropped my house shoe and i already closed up front soi had to unhook everything and get that out, did not want it to catch on that belt i just bought and fixed lol thanks kristal cumpton

Got the washer used. Agitation was okay, but the screw part of the agitator was very weak and kept slipping, so bought a replacement agitator. This DID NOT fix the problem, it remained the same. Watched a video on this site about the part under the agitator, whereupon we saw there was supposed to be a washer on top of the spike-thing where you screw the agitator down. THAT was the problem. That washer was missing, and when we replaced it, the agitation was fixed! Very much appreciate this site.

All I did was push the new part into the machine! So easy!

This repair is realy very easy
As discribed by the others

remove top cover, remove front of dryer, unscrew two #2 screws from gas valve coil hol down bracket. replace coils. reassemble dryer.. works great.. had already replaced the thermostate and flame sensor.. didn't change anything.. the coil set did the trick..

Customer responses / directions were great nothing to add - except no where does anyone mention "high temperature grease" for the Drum Support Bearing - only on the video is it mentioned numerous times. I honestly think it took longer to vacuum out all the lint then it did to do the repairs.

Tensioner (pulley spring) replacement.

The whole tub and motor are suspended by springs so I just got a flat bar and using the edge of the bottom of the washer as a fulcrum, lifted the whole thing enough to be able to shove a 2x4 under there at the base of the dome. It was still tight getting the lock washer off the bottom of the spring axel, but it popped off by pushing the ends with two screwdrivers.

Determined that the coil on the gas valve wasn't pulling in to ignite. Using an ohmmeter, I determined the coil was open. The coil was removed by pulling off the wire connecter and removing the two phillips screws holding the bracket over the two coils. The coil then slides out. I slid the new coil into place, replaced the bracket and two screws and reconnected the wire connector. It worked immediately. The actual repair only took 15 minutes. The bulk of the time was spent tracking down which part had failed.

Very easy to install. Unscrew 2 screws and I was done in minutes. Thanks for the fast part delivery!

I read the last three peoples experiences when I ordered the part on your on line page. I had already made all the wrong mistakes taking the machine apart, and couldn't beleive how simplified it was on your web site. I had called a local repair shop only to be advised the part would take 4 days shipping and the price of it plus shipping was twice what I paid you. Your part arrived the day after I ordered it on line, Thanks again for being there!!!!!

After making sure there was no blockages and the pump was not jammed I knew it was time for a new one . Unplug the machine and turn off the hot and cold water . Remove the two screws on the bottom of the front of the machine and push down on the panel it should come right off . Make sure all the water is drained out of the tub use a wet/dry vacuum to suck out all the water if needed . Then with the vacuum empty squeeze the clamps that hold the hoses on the pump and push them out of the way . Use the vacuum to suck up any leftover water, as you remove both hoses . Unplug the one set of wires going to the pump . Remove both screws and the pump should now be loose . Do the same thing in reverse to install the new pump . Other than dealing with the water it should take under 15 minutes . Good Luck

Took off all controls and panel. Removed the top. Pulled out the drum. Unscrewed shaft and bearing holder. Replaced all parts and started it back up.
--The parts were shipped timely,