GUD27ESPM1DG General Electric Washer Dryer Combo - Instructions

The top and front of the dryer had to come off, and taking off the top (and later putting it back on) was the hardest part. The old seal was stretched approximately two feet longer than the replacement part, and its thinness caused the drum to squeak as it scraped by the door panel. We simply pressed the new seal into place after pulling out the old one. Piece of cake. Putting the front of the dryer back on was simple as well. Fitting the top back into its slots properly was the biggest pain of the whole ordeal. The part came in about 2 days. Thanks!

removed two phillips screws from front panel, removed front panel and raised top cover, had my wife hold up top cover while i removed belt and installed new one, reassembled in reverse order, turned on dryer and checked for proper operation, and yes i did unplug the unit. worked great!!

I removed the two screws inside the door and popped the top loose. I took the top off to see and have access to the interior. I leaned the front out and inserted the belt around the drum (with my wife's help), replaced the screws and laid the dryer on it's face on a rolled up blanket and proceeded to run the belt around the pulleys (two). The drive pulley was easy but the idler pulley, not so easy. I had to figure out how the pulley arm was supposed to provide tension on the belt. I figured it out by looking at the diagram. It was then I found the idler pulley was broken and fell apart in my hand. I advise that a new pulley be installed at the same time as the belt. Everything I read on your web site helped.

Open up the unit's lid first and then removed the front panel. Then I removed the broken belt and then routed the new belt around drum, through the belt tensioner, and onto to the motor pulley. I checked to make sure the belt was securely in place and if it would rotate the drum. Once I was positive it was in place I put the dryer panels back together, plug in the dryer, and tested operation. The only thing that was difficult was trying to figure out the routing of the belt through the tensioner because the old belt wasn't in place anymore. In all it was a 45 minute job.

I removed the front cover and top of the dryer by removing screws visible from opening the dryer door. I then had to figure out exactly how the belt was set around the drum and other pulleys. With the belt around the drum and around the motor rotor, the other pulley had to be very forcibly pushed towards the drum in order to get the belt seated correctly. This being my first dryer repair, I was unsure of how the belt was needed to placed. But eventually figured it out using pictures from the internet. The second pulley required a lot of force and I had to squeeze my hand and arm under the drum of the dryer in order to make the belt fit correctly with enough slack to reach around the second pulley.

4 screws, that was it

open the dryer door, locate the 2 screws that hold the top in place, unscrew them

then locate the 2 screws (located near the top of the dryer (facing toward you) and unscrew them

allow the front of the dryer to tilit out towards you, replace the felt, slide the drum back into place into the front of the dryer, resecure the 2 screws (removed last)

lower top of dryer back in place, being careful to make sure the top clips back in correctly.

re-install the 2 screws that secure the dryer top to the front.

boom, you are done....

Amazingly easy work...

first ,removed two screws from inner door lining.removed top by lifting front up and off.removed two screws holding front panel onto side panels.lift and pull up front panel away from main body of dryer.turned it around watching not to damage wires. remove old felt and install new felt.put everything back together in reverse.dryer works great.

no problem open top remove front install new belt

Removed the top of the dryer 2 screws. procedure
open dryer door. At the top of the dryer door their is
two screws left to right, Remove them and lift top
off. Inside where the top was is two screws left to
right. Remove the two screws and take the front
panel off. Carefull not to pull wireing loose. Lean door against something so you don't have to disasemble wireing. Pull broken belt out and install new belt around tumbler and up and over
tension pulley and pull down and slip over the motor pulley. Your'e done. Reassemble front then
top. My dryer ran just fine after these steps. The question and answers helped me do this.

This is a space saver one piece unit with dryer on top. I first removed ten screws that hold the top on, I then removed four more screws that hold the front service cover on and two last screws that hold the rear service cover on. Now I seperated the front cover of the dryer from the dryer tumbler tub and slipped the new belt around the tub, then at the rear service cover I feed the belt through the tensioner and back onto the motor pully. Now just put the covers back in reverse order of removal and all done! "Piece of cake"
Ron

We watched the video of how to take the dryer apart and how to install the thermostat...after watching the video it was pretty easy

Parts arrived well in time, exactly what was needed. The latch was a snap-in process. The strike require gentile use of a pliers, and went in quickly. Thanks!

Watched the video associated with the repair and followed the instructions, it was easier that I thought it was going to be.

Followed the detailed instructions provided when I bought the parts at the online website. Very good directions diagrams/pictures and explanation of repair effort required

There is a plastic female closure part in the dryer door that wouldn't close tightly around the metal male closure on the dryer. I popped out the plastic square with a screwdriver, popped the new plastic closure in with my thumb. Works great. I never even installed the new metal portion of the latch.