GBD277PDB1 Whirlpool Wall Oven - Instructions

I first removed the door from the front of the oven according to instructions that I found on the Internet from others that have had similar problems. I then removed a total of 8 screws - 4 that were holding the door together, and 2 each for the two hinges that I replaced. After replacing the hinges, I re-installed the 4 screws and then guided the oven door back into place. It took probably about 20 minutes from start to finish, and the news hinges that I purchased solved the problem perfectly.

Remove oven from wall, remove top and back covers.Remove old fan assembly. The new assembly fit right in and works great.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

parts arrived in 3 days along with easy to follow instructions. could not have been easier...made kitchen aid look like a class of clowns...

The only difficult part of this repair was figuring out how to get the oven door off. Most instructions advise you to flip the hinge locking clips, then lift off the door. But this oven does not have hinge locking clips. What it has is holes in the hinges, just behind the hinge pins. To get the door off, you need to open the door and insert some 3/16' pins in those holes, then close the door and lift it off. I almost got this right the first time, but I used 1/8" pins, and they didn't work, too small. It took me a long time to figure out to use bigger pins. Once the door is off, it's just a few Philips screws to work your way down to the glass. There are 4 layers of glass in this door.

I read all the repairs. Turned off power to oven. Was ready to clamp clips so the don't fall behind oven and Crap!! One clip popped off so easy, it went behind insulation. Had to pull oven out. Put wire through, connected everything. Turned power on and oven and broiler work great.

Removed oven from the wall. Take off back panel. Removed thermal overload thermostat. Replaced with new part and works great.

First, I'll say this website made it easy to find and order the part, it arrived quickly and reading others' reviews helped with installation. My Dad and I did the repair together, which really helped - my Dad is an fantastic handyman! We removed the door by lifting it up out of the hinges - a little difficult to get the right angle, but we succeeded with a little wiggling. We disassembled each later of glass/door, keeping each layer in order with screws so we could retrace our steps. I cleaned each layer thoroughly, which added to the time. Unfortunately, just as we were putting the last part on (exterior door with glass), the glass shattered as I tightened the screw! Ack! My Dad said it's because the glass was old and easy to shatter. Maybe I tightened the screw too much? So, back to the website I go to order the next part. We expect it to arrive soon. The bad news: another Christmas without an oven. The good news: my oven is now clean as new (I even removed the back fan cover to clean the fan - couldn't have done that without removing the door) and the parts added up to a fraction of the cost of a new oven.

Had to screw off old terminal block & screw on new one

Like others said, the trick was getting the oven door off. If you don't have the instructions, here's how: Open the door all the way. Shine a flashlight on the hinge, and you will see an open hole about 3/16" diameter below the hingepin and toward the oven. With the door open, put a 5/32" allen wrench or any other comparably-sized metal pin into the hole in each hinge. With the pins in place, close the door as far as it will go, which is almost but not quite fully closed. Put one hand under the door handle, the other hand under the bottom of the door, and pull the bottom of the door down and out. With maybe a little wiggling, it will come right out. That's really all there is to it! Taking out all the glass layers is straightforward; you don't need any instructions to see how to do it.

Removed double oven from cabinet after removing the doors, placing it on a milk crate, needs two people, turned it slightly to access the rear panels, removed panels and lower of the 2 motors and installed new motor, replaced all panels. I now have to check to make sure it is turned on it is so quiet! We lived with this noise so long because the appliance repair people said it was very expensive, about $400.00 to replace the motor, we did it for under $100.00 !!

With some help from my wife.

Removing the door was the first challenge but once the door was off it was a matter of disassembling the door to get access to the interior door. If you remove all pieces and line them up in the order that they are removed you have a good chance for success.

Turned off the power/ unscrewed the oven from the cabinet and slid it out took the back off the oven and the part was right there. What I would like to know is why this happens so frequently? This is the 2nd time and it always happens after the self cleaning is done.

Did not want to remove the pin from the new hinges, so found a proper rod and cut off two half inch pins to use in removing the door. followed the manual instructions. Took all of the screws out but did not notice that the four inside face screws were machine screws while all others were sheet metal screws. Had a little difficulty in getting the four machine screws to engage the bottom holes of the new hinges. Reinstalled the door and all works fine. It is too bad that we could not purchase just a new hinge spring instead of the entire unit. It is kind of a waste. I suspect that self cleaning ovens generate a very high heat which eventually weakens the hinge. The upper oven will likely fail in the future, but at least I know how to repair it.