RBS305PVB04 Whirlpool Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
While in the Self Clean mode and after about 2-1/2 hours the heat stopped.
Removed the over door and set aside on the countertop. Removed the screws from the frame, pulled the oven out and set it on a small bench. Removed the burned out Thermal Overload Safety Thermostat. Replace it with the new TOST. Put the oven in place and secured the oven with the screws to the frame. Put the door on. Made sure it was set right. Turned on the oven heating element and it worked. Then Turned on the broiler heating element and it worked. And that was that. All done and working right.
Was this instruction helpful to you?
Thank you for voting!
Worn and discolored oven door gasket
Removed retainer screw and retainer. Removed old gasket. Installed new gasket, retainer, and retainer screw. Very simple job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rubie from Elgin, SC
- Parts Used:
- WP9759243
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No Heat After Self Cleaning
Turned the circuit breaker off, removed trim and the oven screws, pulled oven out, and placed on a stand in front. Electrical cord was just long enough without disconnecting. Removed the back panel, installed the old thermostat with the new one the same way. Used the same phillips screwdriver for the operation. Installed the oven using reverse order. Turn circuit breaker on, back in business. Prior comments definitely helped me a lot. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angi from Oriental, NC
- Parts Used:
- WP9759243
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The top oven of a double oven would not heat up
After reading other repair reports and talking to a representative, I ordered the thermal overload safety thermostat. Relatively easy to install after removing the oven from the cabinet, only it did not work. After going over the wiring with a voltage meter, we discovered there was no power to the upper oven, only the lower oven was working. Took the panel off the top of the oven and found a wire which was not attached to anything. Never needed this part at all. This oven was purchased from a second-hand store and was used in a remodeling. $52 for part and $100 for serviceman to make the oven operational.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rod from Dripping Springs, TX
- Parts Used:
- WP9759243
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No operation after cleaning
re thermostat/fuse breakage after cleaning: I replaced the part a 2nd time within a year, both times after a cleaning cycle and after 10 years of no similar problem . This time, when putting the oven back, I cleaned all around the door frame and noticed the exhaust grill was heavily filled with dust strands. It's possible this reduced the exhaust enough to overheat the oven during long high temp cleaning and blow the thermo fuse. Just a thought.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julia M from Bronson, FL
- Parts Used:
- WPW10131825, WP9759243
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Oven was not getting hot, neither on Bake or Broil.
I followed the step-by-step instructions from Steve on the part select videos posted on Youtube.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- monte from Spanish fork, UT
- Parts Used:
- WPW10207397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
would not heat up
replace thermal safety switch on back of oven
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marcus from Uppermarlboro, MD
- Parts Used:
- WP9760771, WPW10207397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Baking element stopped working
Removed baking racks from oven. Then I removed two screws from the back of the oven that held the element in place. I disconnected the elements from the spade clips and connected the new element. I remounted the element with the 2 screws and placed the racks back in the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Queen from Bryan, TX
- Parts Used:
- WPW10207397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
The bake element was not heating.
Visited PartSelect.com and ordered the element. Talked to a really sweet lady who assisted me at the company by ordering the part. Received the part and my husband cut off the electricity to the stove, took off the old element, got the sockets and after pushing on the new element, and he screwed the screws back on, cut on the electricity and we cut the stove on and it was ready to go. VERY, VERY SIMPLE TO REPAIR.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Casey from Carlsbad, CA
- Parts Used:
- WP4449259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broke the inside glass on door
Had no problem replacing the glass it took my Husband and I less than 30 min. It took only a screw driver and that's it. Very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Derek from Sun Lakes, AZ
- Parts Used:
- WPW10207397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Lower heating elememt was not working and required replacement
1. REMEMBERED TO SHUT OFF THE APPLICABLE 240V BREAKER. 2. Carefully removed the 2 screws holding the element to the oven structure 3. Carefully extracted the 2 wires from the holes at the rear. 4. Carefully removed the wires from the old element 5. Attached the wire sockets to the new element. 6. Carefully eased the wires back through the holes at the rear 7. Attached the 2 screws through the element holding clamp to the rear wall of the oven. Everything went better than I had expected.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robin from Vanderbilt, PA
- Parts Used:
- WPW10245259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
I had a power serge and it burned the Plug at the termial block and melted a few wire.
After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Waxhaw, NC
- Parts Used:
- WPW10179152
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Remove racks before self-cleaning
Similar to another customer, the racks were not removed before self-cleaning. The issue was that I AM THE HUSBAND and I admit that I did it. Ooops. Great price and if I do it again, I will go back to parts select to get a replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peggie from Gresham, OR
- Parts Used:
- WP4173175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
not needed
screwed in the new oven light
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Richmond, KY
- Parts Used:
- WPW10207397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Element burned out
Took out the 2 screws and removed 2 wires connected to old element, put on new one. Did this all in about 5-10 minutes. Hubby didn't even have to help!
Was this instruction helpful to you?
Thank you for voting!