RBD245PDT14 Whirlpool Wall Oven - Instructions

A generic video on Youtube was actually very helpful as it showed how to remove the door from the oven for easier glass replacement. The only tricky part is getting the panes of glass in the correct order during reassembly,as there are actually 4 pieces in the door. Only the piece that faces the oven's interior was cracked on mine. The two inner pieces between the two outermost pieces are the ones not to mix up. This little repair also gave me the opportunity to thoroughly clean all 4 pieces of glass that had become rather dirty over 12 years. Now the oven door looks like new!

I followed the instructions for installation on your site. I encountered two problems. I was unable to unscrew several screws. I had to used wd40 and slight encouragement from a soft hammer. Also, I was glad for the advice in one instruction about paying attention to the type of screw (flat or more flat). Otherwise, when I was ready to put everything back together, I would have had some problems. The flatter screws definitely had to be used in certain areas.

Had to screw off old terminal block & screw on new one

followed the brief instuctions you provided easy as pie

Remove the door from the oven by rotating the two hinge locks. Place on soft working surface with inside door facing up. Remove screws from side , bottom and top of door. Place screws in groups as they were removed, the heads are different. Do not mix screws. Rotate door so outer Glass front is now on top. Slowly remove inner panel by sliding the outer glass panel towards bottom of door. Carefully remove inner portion of door with the two inner glass panels. Remove inner broken glass from innermost panel. replace with new glass and reverse operations to reassemble door. Make sure the white filler maaterial is back from edge of inner door glass or you will be able to see it from the front after reassembly.When all assembled, slide door back onto hinges relock hinges and you are ready to go.

I found several posts about Whirlpool/KitchenAid ovens having this problem and most of the time this required a replacement of the thermal fuse. Other than the large number of screws to remove the oven and the sheet metal coverings, replacing the fuse was mostly about waiting to get the part. If I had a local dealer with the fuse, I probably could have been baking Deep Dark Chocolate Cheesecake that same evening. Even so, this particular repair should be left to those familiar with doing moderate-level handyman type repairs. You have to make sure the breaker is off and beware of the sharp edges on sheet metal. Fortunately, the fuse was easy to find using online documentation for my model. Part Select was very helpful when my original order did not arrive. Their customer service was great!

Removed trim strip from each side of oven, removed one screw from each side hat held oven in place and slid oven out of wall. Finally found the thermostat located on the back side of the oven after removing the sheet metal on back. replaced the thermostat and reversed the procedure. Only difficult part was locating the thermostat. I thought it was on top, when in fact it was on the back. Pretty easy, really, and saved some cash in the process.

Turned off the power/ unscrewed the oven from the cabinet and slid it out took the back off the oven and the part was right there. What I would like to know is why this happens so frequently? This is the 2nd time and it always happens after the self cleaning is done.

After reading other repair reports and talking to a representative, I ordered the thermal overload safety thermostat. Relatively easy to install after removing the oven from the cabinet, only it did not work. After going over the wiring with a voltage meter, we discovered there was no power to the upper oven, only the lower oven was working. Took the panel off the top of the oven and found a wire which was not attached to anything. Never needed this part at all. This oven was purchased from a second-hand store and was used in a remodeling. $52 for part and $100 for serviceman to make the oven operational.

1. REMEMBERED TO SHUT OFF THE APPLICABLE 240V BREAKER. 2. Carefully removed the 2 screws holding the element to the oven structure 3. Carefully extracted the 2 wires from the holes at the rear. 4. Carefully removed the wires from the old element 5. Attached the wire sockets to the new element. 6. Carefully eased the wires back through the holes at the rear 7. Attached the 2 screws through the element holding clamp to the rear wall of the oven. Everything went better than I had expected.

I followed the instructions given and it was very easy

Visited PartSelect.com and ordered the element. Talked to a really sweet lady who assisted me at the company by ordering the part. Received the part and my husband cut off the electricity to the stove, took off the old element, got the sockets and after pushing on the new element, and he screwed the screws back on, cut on the electricity and we cut the stove on and it was ready to go. VERY, VERY SIMPLE TO REPAIR.

First of all I would like to say how prompt the delivery of my oven glass was. I ordered it Thurs & it came on Sat ~ 2 days thats amazing! Ordering my glass was easy & the representitive that helped me was very nice & the price was great! My husband repaired it in about 20 minutes - very easy to istall the glass & very cost effective repairing it ourselves rather than having a repair man come out! Thanks Part Select I will recommend you to all out fam & friends most definetly!

Not difficult, but there are several layers of glass, metal, and insulation inside this door. Keep track of where the screws go and have room to lay out all the layers. You'll reach the cracked inner glass last.

Turned the circuit breaker off, removed trim and the oven screws, pulled oven out, and placed on a stand in front. Electrical cord was just long enough without disconnecting. Removed the back panel, installed the old thermostat with the new one the same way. Used the same phillips screwdriver for the operation. Installed the oven using reverse order. Turn circuit breaker on, back in business. Prior comments definitely helped me a lot. Thanks.