RBD245PDT14 Whirlpool Wall Oven - Instructions

I looked up the problem and determined I needed to replace the limit switch which is inside the back panel. As a 78 year old woman who isn't afraid to tackle these problems I found this easier than most. Just be sure to disconnect the electrical connection if you don't have long enough length to pull oven from the wall cabinet. I won't put any sheet pans in the oven next time I self clean it.

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

ordered new broiler pan

After we put the latch pins in, the door was easily lifted off. We placed the door on the table and unscrewed the trim pieces. The new trim pieces went into place after we cleaned the door. We slipped the door back on the oven and removed the hinge pins.

Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

Simple - Removed oven door attached retainer with screw.Re attached door.

Whirlpool wanted three time the cost of the same parts The only shipping option was Fedex Overnight which was very costly.

Your prices are great "Parts Select".

Jan

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Remove oven from wall, remove top and back covers.Remove old fan assembly. The new assembly fit right in and works great.

I watched a video on line about how to do the baking element. I did not want to take the door off so it made it more difficult to get to the back where the connections are located. The broiler element has screws holding it up where the over element is resting on the bottom. The video said that you should test the conductivity but I did not have the object needed to do that. It was supposed to solve 99% of the problem to just replace it. When it was removed, I could see that it had a hole blown out on the coil. Problem solved without a repairman needed which would have cost alot more and I still would have needed this part.

I did some research on blogs and identified the thermal fuse as likely culprit. Ordered part from PartSelect.com, but had to call the 800 number because the parts diagram doesn't show this fuse, just the thermostat. The fuse is located on the back of the oven, so it must be removed from the cabinet, but that wasn't a huge project. There are a bunch of sheet metal screws holding the top and back covers that must be removed. The fuse is held on by two screws and has two wire connections. Getting the stove out and disassembling is the hard part, but not really difficult if you take your time. I used a foot stool that was about the same height as the bottom of the oven and just slid the oven out on a piece of cardboard. Make sure you turn the power off before starting.

I was able to convince a local mechanic that he could do this after watching it done four times. The most difficult part was unscrewing and taking out the oven to get to the back. He suggested since this has happened everytime I used the self-cleaning feature, that I cut a hole in the wall for easier access (tongue-in-cheek). The most difficult part was dealing with the extended warranty service plan - this is covered, but they could not find a technician to do this. Then I found out they don't pay mileage so who would want to come out to a rural ND ranch to repair an oven?

Removed oven from the wall. Take off back panel. Removed thermal overload thermostat. Replaced with new part and works great.

Took the door off, removed the screws, took door cover off, cleaned the other two pieces of glass and the new one, and then reassembled. I set the screws aside so I put them back in the same holes. I never want to take the chance of a possible cross threaded screw not going back into the same hole. Note:Now is a good time to clean edges with oven cleaner before reassembly.

Removed double oven from cabinet after removing the doors, placing it on a milk crate, needs two people, turned it slightly to access the rear panels, removed panels and lower of the 2 motors and installed new motor, replaced all panels. I now have to check to make sure it is turned on it is so quiet! We lived with this noise so long because the appliance repair people said it was very expensive, about $400.00 to replace the motor, we did it for under $100.00 !!