RBD245PDQ11 Whirlpool Wall Oven - Instructions

re thermostat/fuse breakage after cleaning: I replaced the part a 2nd time within a year, both times after a cleaning cycle and after 10 years of no similar problem . This time, when putting the oven back, I cleaned all around the door frame and noticed the exhaust grill was heavily filled with dust strands. It's possible this reduced the exhaust enough to overheat the oven during long high temp cleaning and blow the thermo fuse. Just a thought.

replace thermal safety switch on back of oven

I followed the instructions given and it was very easy

The repair went well & the part came in on time for thanksgiving thank you

Actually I ordered the rong part--I ordered a control panel when I should have ordered a control board but Partselect did a great job of sending what was ordered also a nice job of letting me return it for credit. they did a great job of what they do and I would recommend them to all.

Not difficult, but there are several layers of glass, metal, and insulation inside this door. Keep track of where the screws go and have room to lay out all the layers. You'll reach the cracked inner glass last.

Turned the circuit breaker off, removed trim and the oven screws, pulled oven out, and placed on a stand in front. Electrical cord was just long enough without disconnecting. Removed the back panel, installed the old thermostat with the new one the same way. Used the same phillips screwdriver for the operation. Installed the oven using reverse order. Turn circuit breaker on, back in business. Prior comments definitely helped me a lot. Thanks.

This site helped me diagnois the problem rating the suggested problem as a 99% chance cause of the problem. Ordered the thermal overload safety thermostat and it arrived in just two days. Repair was quick and easy once getting the oven removed from the cabinet. (It's very heavy so have some assistance or a sturdy stand to set it out on.)#2 Phillips scredriver and needle nose pliers were only tools needed. Overall, an easy repair for anyone.

Visited PartSelect.com and ordered the element. Talked to a really sweet lady who assisted me at the company by ordering the part. Received the part and my husband cut off the electricity to the stove, took off the old element, got the sockets and after pushing on the new element, and he screwed the screws back on, cut on the electricity and we cut the stove on and it was ready to go. VERY, VERY SIMPLE TO REPAIR.

After reading other repair reports and talking to a representative, I ordered the thermal overload safety thermostat. Relatively easy to install after removing the oven from the cabinet, only it did not work. After going over the wiring with a voltage meter, we discovered there was no power to the upper oven, only the lower oven was working. Took the panel off the top of the oven and found a wire which was not attached to anything. Never needed this part at all. This oven was purchased from a second-hand store and was used in a remodeling. $52 for part and $100 for serviceman to make the oven operational.

Turned off the power/ unscrewed the oven from the cabinet and slid it out took the back off the oven and the part was right there. What I would like to know is why this happens so frequently? This is the 2nd time and it always happens after the self cleaning is done.

I did some research on blogs and identified the thermal fuse as likely culprit. Ordered part from PartSelect.com, but had to call the 800 number because the parts diagram doesn't show this fuse, just the thermostat. The fuse is located on the back of the oven, so it must be removed from the cabinet, but that wasn't a huge project. There are a bunch of sheet metal screws holding the top and back covers that must be removed. The fuse is held on by two screws and has two wire connections. Getting the stove out and disassembling is the hard part, but not really difficult if you take your time. I used a foot stool that was about the same height as the bottom of the oven and just slid the oven out on a piece of cardboard. Make sure you turn the power off before starting.

Did not want to remove the pin from the new hinges, so found a proper rod and cut off two half inch pins to use in removing the door. followed the manual instructions. Took all of the screws out but did not notice that the four inside face screws were machine screws while all others were sheet metal screws. Had a little difficulty in getting the four machine screws to engage the bottom holes of the new hinges. Reinstalled the door and all works fine. It is too bad that we could not purchase just a new hinge spring instead of the entire unit. It is kind of a waste. I suspect that self cleaning ovens generate a very high heat which eventually weakens the hinge. The upper oven will likely fail in the future, but at least I know how to repair it.

followed the brief instuctions you provided easy as pie

I followed the instructions for installation on your site. I encountered two problems. I was unable to unscrew several screws. I had to used wd40 and slight encouragement from a soft hammer. Also, I was glad for the advice in one instruction about paying attention to the type of screw (flat or more flat). Otherwise, when I was ready to put everything back together, I would have had some problems. The flatter screws definitely had to be used in certain areas.