RBD245PDQ11 Whirlpool Wall Oven - Instructions

Remove the door from the oven by rotating the two hinge locks. Place on soft working surface with inside door facing up. Remove screws from side , bottom and top of door. Place screws in groups as they were removed, the heads are different. Do not mix screws. Rotate door so outer Glass front is now on top. Slowly remove inner panel by sliding the outer glass panel towards bottom of door. Carefully remove inner portion of door with the two inner glass panels. Remove inner broken glass from innermost panel. replace with new glass and reverse operations to reassemble door. Make sure the white filler maaterial is back from edge of inner door glass or you will be able to see it from the front after reassembly.When all assembled, slide door back onto hinges relock hinges and you are ready to go.

With some help from my wife.

re thermostat/fuse breakage after cleaning: I replaced the part a 2nd time within a year, both times after a cleaning cycle and after 10 years of no similar problem . This time, when putting the oven back, I cleaned all around the door frame and noticed the exhaust grill was heavily filled with dust strands. It's possible this reduced the exhaust enough to overheat the oven during long high temp cleaning and blow the thermo fuse. Just a thought.

replace thermal safety switch on back of oven

First of all I would like to say how prompt the delivery of my oven glass was. I ordered it Thurs & it came on Sat ~ 2 days thats amazing! Ordering my glass was easy & the representitive that helped me was very nice & the price was great! My husband repaired it in about 20 minutes - very easy to istall the glass & very cost effective repairing it ourselves rather than having a repair man come out! Thanks Part Select I will recommend you to all out fam & friends most definetly!

The repair went well & the part came in on time for thanksgiving thank you

Took out the 2 screws and removed 2 wires connected to old element, put on new one. Did this all in about 5-10 minutes. Hubby didn't even have to help!

Actually I ordered the rong part--I ordered a control panel when I should have ordered a control board but Partselect did a great job of sending what was ordered also a nice job of letting me return it for credit. they did a great job of what they do and I would recommend them to all.

Have a Whirlpool Accubake self cleaning wall oven that quit working after doing a cleaning. Found that the thermal overload safety thermostat might be the problem. Ordered the part which arrived in a couple of days. Installation was very easy and took about 10 minutes. First turn off power to the oven. Slide the oven out, remove the back panel, remove the old safety thermostat which has two wires coming off of it, and replace it with the new one. Put the back panel on and slid the oven back in. Turned the power to the oven back on and we had heat. Problem solved.

Went to PartSelect on the internet and looked up my model. Next I selected the problem from a short list of questions, which indicated the broil element was the problem 99% of the time. With this bit of confidence I ordered the part which was delivered in 2 days. The first step in the repair was to turn off the circuit breaker for the oven. After removing four screws that held the broil element in the oven, I pulled the electrical connectors apart on each end of the old element and attached the new unit to the electrical leads. Lastly I pushed all the wiring back inside the back wall of the oven and replaced the four mounting screws. I then performed ops check, which worked. End of story, job done in about 10 to 15 minutes. Easy Peasy.

Removed with screw driver the gasket clamp at bottom of door opening and then pulled away the old gasket. Installed new gasket making sure that each holding pin was insert in mounting holes, trimmed away un-raveled gasket material at ends and reinstalled gasket clamp at bottom of door. Removed old oven racks and installed new racks.

Removed the old element by taking out two screws and replaced the new unit using the same screws. The delivery time on the new element was very quick-about two days. Thanks.

Ordered the part from partselect.com. I was amazed that it arrived the next day! It was the easiest repair I ever did. Took out 2 screws, unplugged the wires from the old element, plugged the wires into the new one, and replace the screws. Done.

Contacted repair person on line and explained the problem. Person suggested testing the thermal fuse. Checked for continuity and there was none indicating the fuse was blown. Ordered new part and installed. Everything working again. Only problem was that the new part did not have the same connection as the old one on one end. Made substitution and it worked.

Killed the power to oven, removed oven from its enclosure (its heavy), removed back off oven and the part that needed to be replaced was right there. After that simply reverse the procedure. Honestly hardest part of whole job was remembering what i did with the screwdriver after my last home repair job. The oven is heavy you may need help.