L3581XRA Norge Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Charles from Avoca, PA
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
lower oven heating element failed
Power off by unplugging appliance!
Remove the old element by removing one screw from each of the old element anchoring tabs.
Pull element away from back of oven approx. 3 inches to expose spade lug electrical connectors.
With the pliers, gently seperate the spade connector from the element connecting tab.
Remove old element.
Install new element in reverse order.
Plug appliance in, set oven to warm/low heat to test and burn off any metal preserveative from elemnt surface.
Check operation by allowing to heat for < 30 seconds. Oven element should start to warm and can be confirmed by breifly placing hand a few inches away from element to detect heat.
Turn oven off if satisfactory. Reset time on oven clock. Finis!!!!
Remove the old element by removing one screw from each of the old element anchoring tabs.
Pull element away from back of oven approx. 3 inches to expose spade lug electrical connectors.
With the pliers, gently seperate the spade connector from the element connecting tab.
Remove old element.
Install new element in reverse order.
Plug appliance in, set oven to warm/low heat to test and burn off any metal preserveative from elemnt surface.
Check operation by allowing to heat for < 30 seconds. Oven element should start to warm and can be confirmed by breifly placing hand a few inches away from element to detect heat.
Turn oven off if satisfactory. Reset time on oven clock. Finis!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from davie, FL
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
old element broke
unscrew 2 screws, pull 2 connectors off, put in new part in reverse order - easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Dover, DE
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The bake element sparked then burned up
This is the second time I have replaced the bake element. It looks like 8 years is about as long as they last under normal use. The repair was simple; remove 2 screws, pull the bake element out, disconnect the wire connected to each end of the bake element, then reverse the process to reinstall.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Sun City West, AZ
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Element burned out
Removed old element (two screws) unclipped two wires. Clipped the two wires to the new element (one at each end), reinserted new element, replaced the two screws. Done. Oh, flipped the circuit breaker back on:-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Elkin, NC
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bottom baking element blew out
unscrewed the old baking element, took the yellow wire off, and put the yellow wire onto the new baking element and screwed it back onto the oven. Took less than 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty Mae from Canton, OK
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven would not heat
1. Turned off electricity to oven.
2. Unscrewed old oven element. Found it had burned through
on the underside.
3. Inserted & screwed in new oven element.
35 year old oven good to go.
2. Unscrewed old oven element. Found it had burned through
on the underside.
3. Inserted & screwed in new oven element.
35 year old oven good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Valhalla, NY
- Parts Used:
- WP74003019
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The oven did not heat up. I noticed the element was cracked.
I watched the video provided by Part Select before I ordered the part. I removed the old element by taking out two screws and unplugging it from the wires. I put the new element in place, connected the wire to the right side and then opened up the back of the range to connect the left side. The repair was easy, but the video did not show that you had to connect the left side from the rear of the appliance. It was easy to figure out. The appliance works like a charm...no like an oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amanda from Columbia, MO
- Parts Used:
- WP74003019
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
heating element burned out
We repalced the heating element n no time. Easy to do and the price couldn't be beat!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- melissa from moultrie, GA
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
the bottom element was bad.
I removed the element from the back of the oven.Then i removed the wires from the bad element. I then attached the wires to the new element,and screwed it into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from Harlan, IA
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
baking element burned out
Watched the video provided and followed the instructions. I couldn't believe how simple it was to fix the problem! I ordered the part Sunday evening and it was sitting in front of my door Tuesday afternoon. Talk about service! I couldn't be more pleased with the convience of fixing my problem right from my own home. Thank You!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Oakland, CA
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The oven would not heat for baking
Disconnect the electrical cord, remove the oven racks, remove the screws holding the bake element with a screw driver, pull out the bake element, then replace it with the new element. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeffrey from st louis, MO
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
heating element broke
Very easy, clip on connections and two screws to hold it in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fran from Bryan, TX
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Element burned out
Called Sears, repairman couldn't come for a week and would cost $129 for visit not including parts. Went to Sears repair store, part cost more than the part I had already found online and would take a week to arrive. Ordered the part online, paid for next day delivery, watched a video on how to replace. Had my oven back in two days and $59!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- beverly from bloomsburg, PA
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
element burned up
I am a 62 year old woman. All I had to do was unscrew the retaining screws on the back of the oven wall, pull the element out and unplug it. When the new one came, I did it in reverse. It took about five minutes. Ps: I did turn the breaker off first....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maryrose from Normal, IL
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
baking element quit heating
first I took the opportunity to clean the oven really well, Turned off the electricity at the breaker box, Took out the screw on each side and pulled out to view the clips they were attached to, they came off easily, I attached the new ones pushed in to place and reattached the 2 screws. Easiest thing I've ever done and was so cost effective to do this instead of replacing the stove. Works great!I can't believe it was shipped so quickly. I will be shopping here in the future!!!
Was this instruction helpful to you?
Thank you for voting!