L3581XRA Norge Wall Oven - Instructions

We actually had to get the repairman back that had repaired our microwave. Our range has the attached microwave above the range. My stovetop light worked prior to the visit. When he left, I prepared supper without the light, which did not go on. Ultimately, we had to replace the fluorscent tube, which thankfully, you had. No appliance store in a 35 mile radius did. We finally got the glass protector off, and the new tube did not go on. Back to the repairman, to tell him the new bulb did not work and that probably something happened when he visited before. He came back, found that indeed a wire had been broken when he was working on the microwave. I had indicated to him I did not expect to pay another repair bill after I had alrealy spent 117. before plus the cost of the new bulb, 22. something including shipping. He obliged and id not charge me anythink to repair the broken wire.
Now I have the old bulb for back up!!!
Thank you for having my replacement tube!!

first I removed the 2 screws, I then pulled the element out., accidently lost one of the wire in the insulation and had to take the back panel off which was 8 screws. Probably doubled my time. I received my part in 4 days thanks to good service and FedX It arrived the day before Thanksgiving. Just in time, Thank You All.

I was blown away by how easy it was to order and receive this replacement part. I went on the web on Christmas afternoon, Googled "Magic Chef" and found your website. Your ordering process could not be easier (including the on-line drawings and all). I selected the lowest cost shipping method "3-5 days." Wednesday evening, I got your e-mail with the tracker. Thursday afternoon the part arrived! Saturday, we opened the oven, took out the old unit, and put in the new. It worked fine! Thanks again!!

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

removed drawer from track replaced supports on track and one on the drawer.

Called repairman, he never called back for a week. Gave up and found your website, ordered the part. You said it would take 3-5 business days. You lied, it was there the next day. Taking old element out starts with shutting off the juice. Remove trays, pans, etc. Unscrew two screws, pull out elements ends, unclip from wires, reverse the process with new one. You need a light to do this.

Broken part was already removed, so I used the screw from the broken support and installed the new support. Very simple, easy, and painless.

the new elements were super easy to replace. the old ones just pulled out and the new ones easily pushed in. the top one was a little more difficult only because it had brackets that had to be slid of and then slid onto the new one.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires reverse the order to install the socet was easy but after i was done discovered that the base of the old bulb was stuck in the socet keeped it for future use

Replaced the element.

This was a snap. It took me longer to find the right part number than it did to make the repair. After securing power to the oven, I removed the racks. I then unscrewed the element supports and pulled the element out slightly to expose the connectors. Using a pliers I removed the connector from each side of the element. At this point, I should have placed a piece of electrical tape to prevent the connector leads from slipping back into the body of the oven. Instead, I fished them out with a tweezer, and slid the connectors back onto each side of the element. I then screwed in the elements supports, replaced the oven racks, and restored the power. It literally took less than 10 minutes.

Super simple. My husband ordered the part. It arrived in 3 days. The old element plugs right into cables on both sides of the back of the oven and are secured to the rear wall with screws. I unscrewed the plates, detached the wires on each side and slid the new ones in place. It was that easy and took me about 10 minutes.

Simple repair.Just make sure you measure the length of element from back wall to plug in,width,and width of holes in back of oven.Simple repair with correct measurements.Pluged it in replaced screws plugged power back to unit , worked like a charm....Thank You!!!

Removed back of stove (6 screws), puled clips loose. Two screws inside oven, pulled out old element. slid new one in, replaced screws, slid on clips replaced back panel. Don't forget to unplug the stove frist.

Took out 2 screws pulled off the 2 female connectors. put the conectors on the new element and put the screws in. It took less than 10 minutes