CWG3100AAS13 Maytag Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Daniel from Wonder Lake, IL
- Parts Used:
- 74007498
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench (Adjustable)
Would not heat up
Bought the igniter, replaced it with the old one and it works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Dearborn Heights, MI
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The Oven would not light
I called the yellow pages repair man and he quoted me $450 to replace the igniter. I did it myself for $63 and it took 10 minuet's. I'm gonna get a T shirt that says "Mr Fix It" Next is the refrigerator door gaskets! Someone from part select had mentioned that to take the door off the oven you "just open the door a little and lift it off". that was a helpful hint because I would have been looking for screws for half a day!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nina from Saint Albans, VT
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would NOT heat up!!
Open the oven door, take the bottom out. The ignitor is right there!! unscrew it and unplug it... plug in and screw in the new one! Took about five minutes!! Our oven worked again after not working for a year!! Yeah!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ricky from hollister, CA
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven would not heat up over 200
unplugged range took the oven racks out removed bottom plate, removed 2 screws from the igniter, wiggled the connector out of the hole, unplugged the connector. reconnected the connector reattached the igniter and put the plate and racks back in plugged the range in and it works just like it should. took about 15 mins. easier than I expected.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from Alpharetta, GA
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Gas smell and oven won't get hot, or takes too long.
I turned off the gas supply and unplugged the power source first. Then I removed the old igniter, by removing the plug wire clip from the back of the stove. I then removed the oven door by simply sliding it up and off the track. Once the oven door was removed I could easily access the igniter after removing the heat shield at the bottom of the stove. I had to remove two screws that mount the igniter. I had a little problem removing one screw, because it was stripped, so I had to use my Dremel tool to cut off the screw. Once it was removed the igniter was easily replaced with the new one. My wife and I was really excited that the fix worked! Saved me hundreds of dollars. Money I used for the holidays. Thanks Part Select!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Morrow, OH
- Parts Used:
- 74007498
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Igniter would glow but not light the stove
I replaced the igniter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Centuria, WI
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Would not light
Got the part, changed it, works great. That's all
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gary from weston, WV
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
oven would not light and gas fumes came out before lighting
took the top oven door off because you need to reach back to take off the igniter it take a 1/4 inch socket to do this only 2 bolts or screws then slide to stove out a bit to reach the plug in the back of stove its a clip type plug in it don't matter it plugs one way cant get it wrong that it put the new on but slide the plug through the hole in the back of the oven first then bolt it back and your put the clip on in the back of the stove. turn it on. mind came on fast and that is what you want it to do your done. this repair is in the bottom in the broiler area might need a flashlight to see with.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Barrington, IL
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bad igniter
Shut off power, pulled oven out, shut off gas, removed racks and bottom cover. Two bolts held the igniter on, remove those and feed the electrical connector plug through the back of the oven and replace igniter. Be sure the bolts are not too rusty as one if them sheared off and I had use a pair of side cutters to hold the screw while I removed the broken section of the screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Magnolia, TX
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven would not lite
used screwdriver to replace oven igniter , we are planning to buy a new oven in the future , now we can buy it when I can better afford it. Thank you for you help I'll be back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Oceanside, CA
- Parts Used:
- 74007498
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven would not light
Suspected the igniter, and verified by reading comments on your parts site. The mounting screws were frozen so I used larger screws. Piece of cake! Wa La!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Park Ridge, IL
- Parts Used:
- WP7212P006-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Insulation along the top of the oven cracked and broke off
Took old insulation off and replaced it with new by hooking new part in its place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Marengo, IL
- Parts Used:
- 74007498
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Ignitor glows but oven doesn't ignite or ignites then turns off.
1.) Remove door from hinges (open slightly and pull up). 2.) Remove racks. 3.) Remove oven floor to expose burner. 4.) Remove wing-nut and burner cover. 5.) Remove two ignitor mounting screws. 6.) Pull wires and connector through back wall. 7.) Connect new ignitor and mount to burner. 8.) Replace components in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from North Hills, CA
- Parts Used:
- WP7212P003-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door gasket broken
This part showed up so fast I couldn't believe it. Took longer to unwrap the package than to install the gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Three Forks, MT
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would not light.
Removed oven bottom. 2 screws and igniter was removed. 1 screw for back panel unplugged igniter.
Was this instruction helpful to you?
Thank you for voting!