CWG3100AAS13 Maytag Wall Oven - Instructions

First I unplugged the range, turned off the gas to the oven and disconnected the gas line from the oven. I pulled the oven out to gain access to the rear of the unit and unplugged the old igniter. Next, I removed the oven door, removed two screws to the floor of the oven and removed it. I then removed the metal covering above the gas component allowing full access to the igniter. I removed two screws from the igniter and removed it. I positioned the new igniter and replaced the two screws. I replaced the covering over the gas component, replaced the oven floor and put the oven door back on. I went to the rear of the unit and plugged in the new igniter. I then reconnected the gas line to the oven range and checked for leaks, No leaks were found and I pushed the oven unit back into place. I pushed the Bake button and the igniter started igniting the oven.

Job completed.

Removed the old igniter, followed the wires. Reversed the process and put it back together. Saved big bucks! Thanks for the quick service.

followed instructions from repair manual.

The repairs was easy,once I found the problem I turned the gas off and unplug the power supply cord. For the oven gas valve I used a 5/8 wrench to take the gas supply line away from the side of the valve inside the over. I used a 1/4 nutdriver to remove the two screw holding the braket down over the valve. For the glow-bar I donnected the power supply plug and used a 1/4 nutdriver to remove two screw holding it in place next to the brun.

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

First i removed the two screws that hold the element in place. I then pulled the wire out of the hole and disconected the plug. then plug in the new one, put the two screws back in, and checked it to see if it worked,It worked like a new one! So as my reward my wife baked me cookies!

It took all of 10 mins. Open oven door slightly lift to remove.took out shelves and bottom of oven,lift at back to remove.Two screws hold the Igniter, was able to pull the connector into the oven to change. Oven works great!

This is simple for most people - unscrew and remove the bottom oven floor pan. There is the igniter, removed with two screws with a 1/4 nutdriver. However, my problem was that when I unclipped the old igniter, I dropped the over part of the connection, it fell down the hole, through the insulation, to the bottom of the stove where the wiring is. I had to pull out the stove to get to the connection, push it back up the hole to the oven, then install the igniter. My advice: do no lose your grip on the oven wire whatever you do. Otherwise, it was a snap, even for a klutz.

took the top oven door off because you need to reach back to take off the igniter it take a 1/4 inch socket to do this only 2 bolts or screws then slide to stove out a bit to reach the plug in the back of stove its a clip type plug in it don't matter it plugs one way cant get it wrong that it put the new on but slide the plug through the hole in the back of the oven first then bolt it back and your put the clip on in the back of the stove. turn it on. mind came on fast and that is what you want it to do your done. this repair is in the bottom in the broiler area might need a flashlight to see with.

i took out the new peace from the frame and i replaced into the old frame then i chopped the new plug also chopped off the old plug i connected the wires with electric tap then it got ready to plug in the new peace

removed oven door, removed all shelving....unplugged the electrical cord........unsrewed the igniter(2 screws)removed some of the insulation on back of oven that was covering the wire and plug......disconnected the wire plug...........reversed the process and 15 minutes later I was done............the oven works great.......the new igniter arrived 2 days after I ordered it. thanks

Got the part, changed it, works great. That's all

My top burners and broiler were working fine so I knew it was not a gas pressure issue,after reading other peoples oven issues I felt comfortable that my problem was the oven igniter, the igniter was only building about 50 to 75 percent of the normal glow/heat needed, thereby not creating enough heat to trip the sensor that opens the oven burner gas valve. 2 Screws hold a drip pan which after removed allow access to the igniter. 2 Screws hold the igniter in. You need to access the rear of the stove to plug in the new igniter connector at a 1 screw access panel in the center of the back of stove. My oven has been working great since the repair. I would recomend partselect anytime, I ordered the wrong igniter, the diagram is confusing so be carefull , and had to send it back , I got my refund in less than a week. Good luck from beautiful western new york state.

This oven is part of a stand-alone gas (propane) stove. It was purchased and installed in July, 2005. The igniter I ordered from PartSelect arrived as promised. But the connecter on the new igniter did not match the connecter on the old one. I had to either find an igniter with a compatible connecter or splice the old connecter to the new igniter; I chose to splice. Now, I'm not a real handyman, and I'm especially skittish around electricity. But I found two wire connecters (plastic tube-like things with metal interiors). I stripped about a 1/4-inch from all four wires and inserted them into the wire connecters, making sure the igniter was properly placed so the screw holes lined up. Then I used the crimper tool to crimp the wires together. I did a pull test to make sure the wires were secure, replace the now connected wires in their proper place and turned the oven on. It worked! On this particular stove, you'll need a screwdriver to remove the vent cover, exposing the igniter wires. Due to the gas connection in the back of the stove, you can only pull the stove out so far. So, there's not a lot of room to work in the back of this stove; that's why it took a lot longer to complete this job than the wiring inself. I'd say no more than fifteen minutes. Of course, if all the parts are compatible, even less. Good luck!

The igniters burn out periodically, light bulbs, and have to be replaced. There are two of them, one for the oven and one for the broiler. To get access to the one for the oven, I removed the shelves and the floor of the oven. It lifts out. Two screws hold the igniter to a mounting bracket by the burner. The wires on the igniter pass through a hole in the back of the oven. There was not be enough slack in the wire to get the connector through the hole, so I had to get acess to it from below. I removed the storage drawer from the range. At the back, behind the drawer is a panel that's held on by two screws. I removed the panel and disconnected the igniter wires. I fed the new igniter wire through the hole in the oven and connected it. Then I replaced the panel and the drawer, screwed the igniter in place and replaced the floor of the oven.