CWG3600AAS13 Maytag Wall Oven - Instructions

First off...there are 2 possible oven igniters for this model, and you must determine which one you have. Remove racks from oven.Remove oven door. There are 2 latches(tabs) on the oven side of the hinge.Pull these forward and down. Close the door approx. half way and it will lift straight up. Carefully lay the door aside.There are 2 Phillips head screws at the rear of the pan. They are steel, and may be rusted in place. I used a Dremel with a cutoff wheel to cut a slot in the top of the screw. Then I used a straight blade screwdriver with a pair of pliers on the shaft to assist removing the screws.The oven pan lifts up at the rear to remove.Use a nut driver to remove the 2 screws holding the igniter. Mine were stripped.They use a machine thread in light gauge sheet metal. Then use an air ratchet to put them in. Take a trip to the big box store and get some short stainless sheet metal screws to replace the damaged screws.Pull the wire through the insulation, unplug the old igniter and plug the new one in. Fish the plug and wire back through the insulation. Attach the new igniter with the new screws. Replace the pan with new screws, and reverse the procedure to install the door. Even with the purchase of the Dremel, you will still save a chunk of cash, and you get a tool for the arsenal. It's rare when you don't encounter some problems, with any job. The secret is not burying yourself with more problems you create.

The igniters burn out periodically, light bulbs, and have to be replaced. There are two of them, one for the oven and one for the broiler. To get access to the one for the oven, I removed the shelves and the floor of the oven. It lifts out. Two screws hold the igniter to a mounting bracket by the burner. The wires on the igniter pass through a hole in the back of the oven. There was not be enough slack in the wire to get the connector through the hole, so I had to get acess to it from below. I removed the storage drawer from the range. At the back, behind the drawer is a panel that's held on by two screws. I removed the panel and disconnected the igniter wires. I fed the new igniter wire through the hole in the oven and connected it. Then I replaced the panel and the drawer, screwed the igniter in place and replaced the floor of the oven.

Suspected the igniter, and verified by reading comments on your parts site. The mounting screws were frozen so I used larger screws. Piece of cake! Wa La!

Removing the oven door by partly opening it and pulling it up out of the hinge made access to the igniter much easier. Access to the igniter was easy. Just remove the baking shelves and lift out the bottom panel. I removed the two screws holding the old igniter. One screw was difficult to remove because of oxidation, and required some tinkering as the threads were stripped. But once the screws were removed, the igniter was easy to replace and connect to the gas controller with a simple plugin connection.

Followed the instructions that were provided me when I ordered the Gas Oven Igniter

used screwdriver to replace oven igniter , we are planning to buy a new oven in the future , now we can buy it when I can better afford it. Thank you for you help I'll be back.

removed oven door, removed all shelving....unplugged the electrical cord........unsrewed the igniter(2 screws)removed some of the insulation on back of oven that was covering the wire and plug......disconnected the wire plug...........reversed the process and 15 minutes later I was done............the oven works great.......the new igniter arrived 2 days after I ordered it. thanks

Took off oven door. Took out oven racks. Took out bottom oven cover above igniter. Igniter is held in by 2 screws,took them out with a small socket. Went to back of stove and unhooked white plug in - (part of igniter) Thats it. About as easy as it gets. Just reversed the process putting in the new one. Took about 25 minutes. It would have taken less time but I had a problem with one of the screws. Probably from the heat. The oven is 9 years old.

opened the oven door, remove racks, remove lower drawer, unscrew protective panel on lower part, take out the bottom plate, unclip the old igniter, clip in new igniter, put everything back together and you are done!

easy

After reading about my problem, I determined it was the igniter. I immediately ordered one. It came two days later. I took the bottom drawer out and removed the shield. To get to the plug wires, I unplugged the old igniter. I used my power nut driver to take off two threaded screws so igniter could be removed. I then pulled the old igniter out. Plugged new one in and reversed process to install new one. I installed it when I got home from work in less than 30 minutes. all is well. We were looking at buying a new stove for $700.00. I fixed it for less than $60.00. Thanks

The seal is suspended by metal clips at each end, which are inserted into holes in the oven box. The clips on the new seal were a bit too wide to fit into the holes. so I drilled the holes larger, and it worked fine.

i took out the new peace from the frame and i replaced into the old frame then i chopped the new plug also chopped off the old plug i connected the wires with electric tap then it got ready to plug in the new peace

I replaced the igniter.

Took old insulation off and replaced it with new by hooking new part in its place.