MEW6627BAS Maytag Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- George from Interlochen, MI
- Parts Used:
- WP7902P444-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Replace cracked glass.
Pulled oven door out of oven and and replaced glass.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Spicewood, TX
- Parts Used:
- WP71001872
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Clock time display was very faded, barely visible and when the oven temperature and/or timer were activated, the entire display was not visible. User had to guess the temperature and time.
First we disconnected power to the oven. Then we removed the two screws that attached the oven control panel cover to the body of the oven. Next we removed the screws that secured the faulty clock assembly to the control panel. Then we un-installed the three cable/connectors. The two wire cable/connectors were simple pull-outs. But with no instructions in either the Users Manual or shipped with the replacement part, we had no idea how to un-install the ribbon cable. Fifteen minutes later, much trial and error, and simple blind luck, we finally realized that we simply had to lift up the connector ears and the ribbon cable would disengage. Then it was a simple matter of seating the replacement assembly, installing the two screws, re-installing the three cables, reseating the control panel cover and re-installing the cover screws. Once power was restored to the oven, the clock was reset. We tested the oven temperature and the timer. All was well once again.
Question: Would you like us to return the faulty Jenn-Air part for trouble-shooting?
Recommendation for the future: Send some simple installation instructions. We both have computer manufacturing asembling experience but never worked with a ribbon cable connector like this one. That connector was a major stumbling block for us. A simple changeout turned into a 30+ battle.
But, I would like to thank you for the quick shipment of this part. It was ordered on a Monday and received in Wednesday's mail. That so FAST! and very much appreciated.
Your website is now in my Favorites and in my email address book. Thank you once again for all your help.
Sharon Hall
133 Lake View Drive
Spicewood, TX 78669
830 693-4513
thumper@tstar.net
Question: Would you like us to return the faulty Jenn-Air part for trouble-shooting?
Recommendation for the future: Send some simple installation instructions. We both have computer manufacturing asembling experience but never worked with a ribbon cable connector like this one. That connector was a major stumbling block for us. A simple changeout turned into a 30+ battle.
But, I would like to thank you for the quick shipment of this part. It was ordered on a Monday and received in Wednesday's mail. That so FAST! and very much appreciated.
Your website is now in my Favorites and in my email address book. Thank you once again for all your help.
Sharon Hall
133 Lake View Drive
Spicewood, TX 78669
830 693-4513
thumper@tstar.net
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- frederick from feura bush, NY
- Parts Used:
- WP74009029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
gasket needed replacement on exterior oven door
first the part was ordered but found it way too overpriced. went to an automotive store and bought door edge molding for a lot less. and it was better quality that the original gasket. with the self stick interior of the door edge molding was a fast and simple repair and more secure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Newbury Park, CA
- Parts Used:
- WP71001872
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
double oven electric clock display - unable to read
Turned off oven power. Removed 4 phillips head screws holding the oven panel housing display, unplugged two attached cords and then placed the oven electronic display panel down on a table and removed the 4 hex head screws mounting the display into the housing. Lifted the two levers holding the ribbon into the display panel. This removed the electronic display from the housing. Reversed the process to install the new electronic display. Restored power and voila! It worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clarence from Easton, PA
- Parts Used:
- WP71001872
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
clock did not light up
i did it myself
Was this instruction helpful to you?
Thank you for voting!