CWE9900 Maytag Wall Oven - Instructions

Turned off breaker,opened door with bent coat hanger by sliding right to left the coat hanger to open the door, remover 2 screws holding in the sensor in upper left corner of the oven. Remove the sensor (gently) with the wire connection from back of oven pulling sensor out a out 8 inches . Disconnect plug. Install new sensor with matched harness /.connection, installed 2 screws ,turned on breaker.

I replaced the oven sensor which was easy to replace. A pigtail wire was provided with the sensor which is intended to be installed first so you don't have to reach around the front and back of the oven at the same time. The replacement was easy. However, that turned out not to be the problem. The real problem was the maytag electronic clock control timer, temperature control unit. The part number is 7601P177-60. This device has been discontinued and I was fortunate enough to find the part at a local supplier. Once I replaced this, the problem went away. The oven heats up normally. My original symptom was that when setting the oven temperature to something like 350 degrees, the display would rapidly report heating up the oven to that temperature, and the oven was only mildly warm. If you have that symptom, it is probably not the oven sensor. It is the electronic clock unit. Hope you can find one. If you can't, I think you need to by a new oven. Regards

The "PartsSelect" General discription of the parts funtion helped me to confirm my suspitions that there was some form of temperature registering problem. I whatched the short video they provided on how to change the part out, even though, in this case, it's pretty self explanitory.The part was in my hands a day erlier than promised and in reality, much earlier than I had anticipated from the beginng. It took me all total, 20 minutes to exchange the part out and have the oven in operation again.

removed 2 screws in probe and pulled it out.had to take back off as wire was tangled from factory and couldn't do quick repair

I removed the old sensor via the two screws holding it in, unplugged it and replaced it with a new one.

opened the door; put 12 penny nails in each hinge through the holes for it, removed screws above hinges; slid door off; laid it on a towel on the workbench; removed side/top/bottom screws and laid the outer door aside. removed the screws from the inside of the door, laid the inside glass aside, removed the glass assembly (broken), cleaned the loose glass out, laid the new glass assembly in place, replaced the panels and screws and slid the door on the hinges, removed the nails and closed the door. 35 minutes. Never did it before4. Part fit great! Thanks to partselect for having the discontinued part!

Replace the oven sensor per the excelent easy video you provided

Followed provided video

The heating element in our old old oven broke in half. Luckily we were able to find a replacement part (which we didn't think we would that's how old the oven is)! The part arrived within a couple of days, my husband removed the old element (toughest part was getting the two old screws unscrewed) plugged in the new one and he was done. Took about 5 minutes! I turned on the over to test it was connect properly and it started heating up right away! We are VERY happy !! :o)

Removed racks from oven, unscrewed two screws holding old element in place with philips head screw driver from the back wall of oven. Carefully pulled element from oven to expose connecting wires and then pulled two wires loose from old element. Reconnected wires on new element and carefully reinstalled element to rear of oven interior with two screws removed from original element.

Watched the video and it was as easy as described. Not many things go as easily as this.

Remove screws, remove old coil, place new coil, screw back in. The hardest part of this task is removing the existing screws which are most likely partially corroded and hard to move.

Followed directions as supplied. New part did not work, so it must be in the control unit which is no longer available. So time for a new range.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Remove 2 screws in upper left corner of stove holding sensor in place. Pull sensor out and disconnect plastic electrical connector. Select appropriate adapter (both styles provided with new part) & reinstall. Power up stove and select bake on control unit to test. Works like a charm!