9524WPW Magic Chef Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ann from Schertz, TX
- Parts Used:
- WPY04000048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The broiler element made a loud noise.I immediately turned the overn off. It kinda acared me.
My son-in-law installed the new element. First turn off the electricity and remove oven door. Then unscrew all connections to the element.The back electrical wires come out from the top back oven. The bracket screw faces the oven and the electrical wires are so short there is very little room for a screw driver (get the shortest one you can find..abt as big as your thumb if possible).Once that was out the element came out with no problems.Then it's just reversing the step. Again, that back electical bracket is difficult to get to for install. Also, the new screws in our kit were Philips, but the old ones were flat so check those out before turning off the oven light.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grant from Alexandria, VA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Independence, KY
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating elements (upper and lower ovens) would not achieve the proper temp
Removed the two screws on both elements, pulled the wires off, put the wires on the new elements and put the screws back in. Very easy, works perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Pasadena, TX
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Bake Element Ceased To Bake.
Turn off the breaker. Remove the two screws holding the bake element and disconnect the two wires. Plug the new element in and re install the screws. Trip the breaker back on and test the oven. It works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denver from Denton, TX
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven element would not heat.
Turned power off by switching off the breaker. Removed both racks from oven. Removed two Phillips head screws at back of oven securing the old heat element. Pulled old heat element forward about four inches exposing the two power wires connected to it. Removed the wires from their connectors. Removed old element. Connected new element to power wires and pushed it back in place. Replaced new Phillips head screws. Replaced racks, and turned power back on. Oven was fixed in less than five minutes. Disposed of old element. Life is good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wallace from Lowell,, AR
- Parts Used:
- WPY04000048
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broil element burned out
Removed the oven door, removed old burned element, installed new element. Turned CB back on and tested oven. Reinstalled oven door. Straight forward and easy to follow directions with new element.Local appliance part house said the element was no longer available. Thanks to you I did not need a new oven. Very easy replacement job with normal tools.Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from Thibodaux, LA
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the element broke was old
turned off power unscrewed plate that held in element unplugged socket from old element plugged in new one screwed plate back turned on power works fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Irvin from Pride, LA
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Element was bad
Turned breaker off. Took out two screws holding it in place. Disconnected two wires. Put new element in. Works fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Park Ridge, IL
- Parts Used:
- WP7212P006-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Insulation along the top of the oven cracked and broke off
Took old insulation off and replaced it with new by hooking new part in its place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Rochester, NY
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burnt out element
Very easy. remove two screwa , pull element forward, unplug.Set new element in place, plug in. push back in. Screw in both screws and your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sherri from Topeka, KS
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element not working
Unscrewed two screws, unplugged two small plugs, plugged the new ones in and screwed the screws back in. Less than 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from North Canton, OH
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Very Easy
Changed bake element in oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GERALD from HUNTINGTON BEACH, CA
- Parts Used:
- WP7212P006-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Door seal badly deteriorated
The seal is suspended by metal clips at each end, which are inserted into holes in the oven box. The clips on the new seal were a bit too wide to fit into the holes. so I drilled the holes larger, and it worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebekah from Azle, TX
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven was not heating on bake setting
I unscrewed the old element from the back of the oven. Then I detached the wires and took the old heating element out. I then fit the wires into the new element and screwed it back in using the new screws. It was really easy! I was lucky to have my father in law show me how, since this was my first time to do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jessica from Macon, GA
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Bottom heating element burned out/ broke.
First, we cut the power to the oven and removed the oven racks. I removed the two screws holding the old heating element in (removed easily, I didn't need any WD-40) and pulled the element wiring out of the back of the oven. It took me a while to realize how the wiring was/is connected to the element, but once I did they came off fairly easily with a little coaxing from some pliers. On our model, the wiring thingums fit down onto the element prongs. So, you pull the straight up to remove them. Very technical terms here. After the wires and the new element were connected, I screwed the new element in, turned the power back on and the oven was is excellent working order again.
Was this instruction helpful to you?
Thank you for voting!