9524WPW Magic Chef Wall Oven - Instructions

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I threw away the old pieces.

Then I connected the two wires on the new element. I pushed the wires back in the insulation in the wall of the cabinet. Then I inserted the two screws and tightened them in.

SUPER EASY!!!!!

This $40 part saved me $1500 on a new double wall oven.

Removed 2 screws, pulled element out. My husband used an ohmmeter to see if the electricity needed to be turned off. It showed no voltage. He could not remove electrical connectors by hand, so he used insulated pliers. When he touched the connectors, a shower of sparks covered the inside of the oven and tripped the breaker switch. Then we noticed the pliers were welded to the side of the oven. Thankfully the pliers had insulated handles and he was not hurt. It might be a good idea to put in the instructions to TURN OFF POWER TO OVEN in the breaker panel because our oven was definitely HOT. Oven works perfectly now.

I used tiny amount of WD40 on old screws,let sit for 2 minutes. Tapped the screws(2) of them with a small hammer to wake them up, I had a cordless drill and they backed right out. Pulled the old element out, used needle nose pliers to pull connectors off of the element(wiggle gently) put the new element on, reinserted back in the oven,attached with new screws that came with the element, started the oven. Worked Perfect!!!

I learned that I could clean the window in the oven door. In taking it apart I saw that the gasket had fallen into the oven door. I found the part online, it arrived in three days. I removed the metal part of the door, removed what was left of the old gasket and put in the new one. Put the metal part of the door back on, and it was as good as new.

Turn off power,Lift up and remowe owen door.undo srews that holds owen to cabinet,pull owen out 7 inc.A second person needs to hold owen so it wont tip out.Remove plates on each side so you can see the hinges,romove screws that hold hingesin place,Remove old hinges place new hingesfrom this site .Secure all screws.Put owen door back.done.

turned off power, removed two screws mounting the old element, cut wires, and removed old element, crimped new stake connectors onto existing wiring, attached stake connectors to new element, installed element with two new screws provided, turned power back on.
It would be easier to just slip the two stake connectors off and reinstall on the new element but I elected to install new connectors because the oven was over ten years old and one seemed loose.

i needed a rack for my oven i looked everywhere for one that fit could not find one.my oven is not common due to the fact it is for a very small space and only 18 " wide i stumbled on this site by accident and decided to try it out shipping was very fast and people there are very nice any have alot of knoldge about parts it is very well set up to order with just a modle # i have told my whole familey about this site they did a great job and i will be back for more parts.

Removed the screws that held the element and disconnected it. Placed the new element in the proper place, connected the wiring, and replaced all the screws. The unit worked beautifully, and all is well. My wife is happy.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Clipped the wires back onto new element and used the two stainless screws provided in kit to resecure.

It should be noted that I first called a local Maytag Appliance Co. and inquired about this element. I was told that they would have to order it and it would cost me 68.00 plus tax. I told them I knew what these elements are worth and their price was a gouge. They didn't care. This is a repair that anyone knowing how to work a Phillips screwdriver can perform. Save some money and do-it-yourself.

Thanks Partselect!

The repair was easy. The door pulls off the hinges without any tools. I had to remove four screws ihat held the wall oven in place. I then removed approximately eight trim screws to expose the two screws holding the hinge in place.I then needed to utilize a nut driver to put the screws in the new hinges because the screws cut threads into the hinge as you put them in so they are a little tight and the nut driver makes this step easier.

Fortunately, we had read the instructions on line, because none were included with the part. Still, it was REALLY easy. We unscrewed the two screws, pulled the element away from the back wall and pulled the wires off the contacts at the back. (That was the hardest part, because they were stuck-on well. WD-40 was helpful here.) The one piece of paper that did arrive with the part told us the ground wire was no longer necessary if you use the new screws that came with the part, so we ended up cutting the ground wire off. We then put the other wires back on the new contacts, pushed it back into place, and re-screwed it to the back wall. We have used the oven several times since, and it's all working well.

I removed the two screws holding the element in place and disconnected the two wire terminals.
I then reversed the above steps to insatll the new element. SUPER EASY!!

no instructions on how to replace element. first i removed the 2 screws that held the element to the oven. then i pulled the element out with the wires attached. at first i couldn't tell how the wires were attached - i thought they may have been soldered on. it took awhile for me to figure it out the wires were attached to a part that pulls up off the element part. no solder was needed. after i figured that out, easy to pull the part up off the element part.

The heat sealing strips are elastic type material with hooks on each end. I simply removed the old strips and hooked the new ones in place.
It was easier than I ever dreamed possible!
And my kitchen is now nice and cool.
Pat Morrison
Sanger TX

I removed the two screws that held in the old part. I pulled the element out a few inches.I disconnected two wires from the old element and connected it to the new. Using the screws provided I reconnected the unit. All went well. No need for repairman. 1