KEBS177DBT6 KitchenAid Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Linda from Hilton Head Island, SC
- Parts Used:
- WP4449253
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Cracked Door glass
Ordered the glass and read the other reviews/instructions on the PartSelect site. Also read the instructions in my owner's manual for removing the oven door. The hardest part of replacing the glass was the removal and replacement of the door. Once I had the door out, replacing the glass was as simple as removing about 8 or so screws, lifting off the cover and replacing the glass, then replacing the screws. One of the hinges on the door had closed and I was not able to open it to replace the door, so I had to have a neighbor come over to over his muscle power. The hinge problem should not have happened and without that little issue, this is a simple repair that I'm sure saved me at least $100.00 on repairman! And - I'm a woman!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from BLOOMINGTON, MN
- Parts Used:
- 4396923
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Purchased home but stove had no broiler pan.
Purchased 2 piece broiler pan from this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from San Diego, CA
- Parts Used:
- WP9759242
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven Would Not Heat After Auto-Clean
Very simple. I removed two screws holding the oven in place. Slid oven out onto the kitchen floor - it doesn't really weigh that much. I then removed about a dozen screws holding the back panel in place. I removed the back panel, disconnected the thermostat by unscrewing a single screw and pulled the defective part from the connectors. I then installed the new thermostat, screwed the back panel back on, slid the oven back into place and re-secured with the two screws. Voila! Repair done. The whole procedure took about 15 minutes and was not difficult at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amanda from Indian Harbour Beach, FL
- Parts Used:
- WP4449253
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Cracked inner glass of oven
I used the instructions from another user on this site and the instructions were great. First look in your oven manual to see how to get the oven off-hardest part of repair. Before removing door-duct tape the broken glass. Remove door. Lay door down on flat surface and keep track of screws as you take them out. Remove outer liner-we removed 6 screws total. Replace glass with new glass. Reattached outer liner back onto door. Replace door. This is a GREAT site. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Albuquerque, NM
- Parts Used:
- WP4455525
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven door would not close completely--door eventually fell off
I looked at the schematic provided on the website and removed all of the screws wih a phillips head screwdriver. I took care not to scratch the stainless steel surface by placing the oven door on a carpet. I removed the old bent hinges and replaced them with the new hinges. I aligned the holes and replaced the screws. The entire job took about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dallas from Andrews, TX
- Parts Used:
- WP4449253
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broken glass door
Took longer to take door off than replace glass.The door would have come off easy if I had read the instructions that came with the oven
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from VIENNA, VA
- Parts Used:
- WP4455381
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Worn door gasket, leaked steam while cooking
Used a Phillips head screw driver to remove cover that was covering the over bottom 1/3 of the installed gasket. I then used flathead screwdriver to help remove gasket from the "pins" that were in the gasket that held it to the oven. Installed new gasket inserting pins into the oven. Then I installed cover over bottom 1/3 of gasket. Overall process was very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from San Jose, CA
- Parts Used:
- WP4455523
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Hinges needed to be replaced having been overstrained
I paid for an online advice service (Just answer)after failing to remove the hinges. The advice was not remotely helpful and I have asked for my deposit back.
Here are the steps:
Remove the door: Place the two tiny studs taken from the tongues of the new hinges in the same holes in the old door.
Holding the door just open, lift up and out to remove the door from the oven.
Lay the door on its inside surface, then remove 2 Phillips head screws from both the top and bottom edges of the door to release the front glass assembly. The hinges can now be seen.
Turn the door over and remove four Phillips heads screws to release the hinges, replace with new hinges.
Replace the two small studs in the hinge tongues and replace the door reversing the removal process. Remove and save the two studs (handy if you ever want to clean the glass on the inside)
Here are the steps:
Remove the door: Place the two tiny studs taken from the tongues of the new hinges in the same holes in the old door.
Holding the door just open, lift up and out to remove the door from the oven.
Lay the door on its inside surface, then remove 2 Phillips head screws from both the top and bottom edges of the door to release the front glass assembly. The hinges can now be seen.
Turn the door over and remove four Phillips heads screws to release the hinges, replace with new hinges.
Replace the two small studs in the hinge tongues and replace the door reversing the removal process. Remove and save the two studs (handy if you ever want to clean the glass on the inside)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from Sequim, WA
- Parts Used:
- WP4455525
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven door would not stay completely closed and the light would come on.
First we had to take the oven door off, which proved a bit tricky. There was a release pin which was hard to find and release. Then we had to unscrew the screws and take the glass and inside of the door off to access the spring hinges. Replacing the hinges was pretty easy, as was reassembling the door. The door snapped back into place and voila! the door stayed shut.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Milton from Pasadena, TX
- Parts Used:
- WP4449253
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
inner oven door glass was cracked
Removed the door and laid it flat with the cracked glass facing up. applied duct tape to the broken glass to help hold it together. Removed the screws from the frame holding the glass. lifted the frame off,removed the broken glass and replaced it with the new piece. replaced the frame. and put the door back on the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Portola Valley, CA
- Parts Used:
- WP4455523
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oved door no longer closed tightly
removed door from oven using hinge locking pins supplied with oven when bought (two small screwdrivers might also work). Put door face down on a towel, removed two screw s on top and on bottom edge, removed back of door, then removed the two screws on eac side holding the old hinge springs. installed new hinge spings and replaced the door. no problems and used the opportunity to clean the door glass.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from Black Mountain, NC
- Parts Used:
- WP8203546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Loose terminal caused block to overheat and break
Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Burr Ridge, IL
- Parts Used:
- WP4455523
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Oven door would not close completely
Removed door per manual instructions, then disassembled door components until I could remove the hinges. Nothing wrong with either one visually but, hoping the springs had become weak over time, I ordered replacements from PartSelect, knnowing I had a 30-day return window if my diagnosis was wromg.
It was right. Door now closes just fine.
It was right. Door now closes just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bonnie from Athens, GA
- Parts Used:
- WP4455525
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven door did not close all the way, oven would not work
Gas Oven would not work without door shutting all the way. New hinges fixed the problem! Removing Superba oven door was the challege. Kitchenaid has their manuals available online which you can look up using the model # available on side of oven door. It contained instructions for door removal which required two pins (one in each hinge) inserted in the hinge holes for the door to release when you pull up and out on it. Nails may be used to replace the pins but the tricky part is removing the nails from the old hinges to remove them from slots in oven door. I used a 12 inch piece of small PVC pipe as a lever, inserting the pipe on the exposed portion of the hinge. This released the nails. The oven door must be taken apart which required removal of screws on the inside face, top and bottom of oven door. It went easily back together and the problem was solved.
Was this instruction helpful to you?
Thank you for voting!