79046103300 Kenmore Wall Oven - Instructions

1. Moved stove from against the wall. 2. Unplugged the power supply. 3. Removed the electrical pannel cover. 4. Disconnected the quick connect probe plug. 5. Opened the oven and removed the probe. 6. Installed the new probe. 7. Connected the quick connect plug. 8. Reattached the electrical panel cover. 9. Plugged in the electrical supply. 10. Moved the stove back into its original position. ****Note**** THIS IS THE SECOND TIME I REPLACED THE PROBE. THE FIRST REPLACEMENT LASTED ONLY 5 MONTHS!!!!

Took screws loose, unplugged old one plugged in new one put screws back

We removed the screws holding the old element. Pulled the old element out of the back of the oven and disconnected the connecters (they just pull off). Slipped the connecters to the new element and pushed the element back in the oven wall and installed the screws. The only hard thing was removing the screws, because they had been in the oven for 15 years and were a little corroded.

watched a U-Tube video on this subject.....worked like aa charm!!

Replaced the switch...removed old switch and transferred the wires one at a time to the new switch. Seems to working fine..

Used a screw driver to loosen 2 screws and the pulled the tabs off the old element and installed the new element. I am probably the most "unhandy " guy in the world but this was a snap. I am as surprised as anyone.

repair was pretty simple. i pulled stove out from cabinet and unplugged it. Then i removed the screws that hold the face panel in place and gently slid out panel as far as i could without damaging wires. i had to remove the small switches that control the two two size burners as well as one thermostat on the right side so i can access the nuts holding the plastic end caps in place. i diagramed the color coded wires so i didnt mix them up.took off the old end caps replaced with new caps and put back together.. took about a half hour as this was my first time inside the guts of this stove.. stove is baack in place and as good as new again.

Our neighbor, who is an electrician, watched the video on how to install. Since this switch was substituted, he paused the video several times to see how the wires should be attached. It worked.

After removing pots / pans in cabinet below cook top and turning off the power, I was able to remove the panel held by 2 screws. Pulling the old light out was just a little difficult as it came in pieces. New one popped right in, hooked up terminals, replaced the panel and that was it !!

used two flat bladed screw drivers to get under edge of switch.. pried one side up and unit popped loose... removed electric connection (three prong recep) and plugged in new switch ..pushed into hole and was done... approximately 3 minutes..

The repair went relatively easy. I even cleaned all the layers of parts when they were removed from the glass panel. I have to thank the excellent customer service and super fast delivery. Overall a quite easy task and $$ saving as well!

Started with three screws on outer edge of door, which separated inner and outer door parts exposing the first set of screws on first piece of glass. There are four panes including inner and outer with two between. Keep track of the screws, be careful removing and replacing glass panes (i put mat down to rest glass on)and with nothing more than a screwdriver and windex to remove fingerprints etc from replaced glass, it was a breeze. Good luck! - FK, Bahamas

Gasket has pins that line up with tiny holes around the perimeter of door. Just pull the old gasket off, and snap new one ( with pins) in . Used the butter knife to push ends of gasket in hole at bottom of door. Took about 2 minutes to complete and looks AWESOME! simple. simple, simple! This company ships immediately and the product is described properly. I would buy from this company again!

Moved the stove away from the wall, unhooked the electric cord and the gas pipe. In the oven, undid the two screws holding the probe. Removed two screws and removed the electrical cover panel from the stove back, disconnected the quick connect to the probe and pulled the probe from the oven. Reversding the proceedures, put the new probe into the oven, hooked up the quick connect and replaced the electrical panel cover. From the front, reinstalled the probe with the two screws, reconnected the gas and the power cord and put the stove back into position. It works just fine now!

Figured out that light and door switch started the convection fan on when door is closed. Found the switch defective. Found exploded view online of switch in oven. Had to figure out that the range top needed to be removed to access the switch from inside the top part of oven. Unscrewed at least (6) screws to free up the range top. Squeezed the inside switch clips to allow switch to be pulled out from outside of oven. Disconnected electrical receptacle and plugged into new switch. Pushed in new switch til it snapped into place. Reinstalled range top.