91148365791 Kenmore Wall Oven - Instructions

It was very easy I removed two screws unpluged the sensor and wire spliced it together and also replaced the modual on the top of the stove and it was that easy.

No problem installing oven sensor, but I diagnose the problem wrong, I need to change(ERC-11)control p/n wb27k5140

It was very simple.. first turn off the electricity... next take out the two screws holding the element to the back of the oven... then pull the two plugs apart( male and female ends) ... throw away old part.
put new part in by plugging the male and female ends back together... push back into oven back.. get all insulation back in... put two old screws back in to secure... done.. turn on power...
don't be afraid.. it was very, very easy.

Remove the screws inside the oven holding the back of the element to the rear wall of the oven. These scrrews are a square drive. Pull element forward and remove 2 screws that hold wires in place. Both sets of screws needed to be replaced with a different size. Reverse order to install.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

Shut off the power from the fuse box. Removed p the two screws and plate that attach the element to the wires and back of oven. Installed the replacement element by attaching the wires and reinserting the two screws. Restored power and tested the new element by preheating the oven at 350 degrees and letting it heat for 15 minutes. Works like a charm!

I first removed the broken element by removing the two hexhead screws on either side of the element bracket. Then I gently pulled the wires through the opening and removed two more screws that attached the wiring to the element. I then compared the new and old elements and found a few differences.

First, the screw holes where the wires connect to the element were tiny in the new element, about a third the size of the holes in the old one. Secondly, the mounting bracket was not as long as the original, and the holes to mount it to the back of the oven are located at the top of the bracket, instead of the sides.

Since this was the only element that I have found, that comes close to the original, I decided to make it work.

I took my drill and a small bit and bored out the screw holes, just enough to get a self taping screw to fit and reconnected the wires.

Now I'm not sure that I would recomment the next step to anyone, but I did this: I held the new bracket against the back of the oven and drilled new holes to match the new bracket, and again used self tapping screws. The reason that I don't encourage this is that the new bracket fits just inside of the old opening, but the insulation cannot be seen as long as the element does not get moved. I then plugged the original bracket holes with the original hex head screws.

It took a little more time and effort than I had expected, but well worth it, after eight months without the use of my oven.

Removed burned out element and discovered replacement element had a different back plate and different hole pattern. Also, the electical connecttion from power wires to ends of element were a TOTALLY different size, both in hole size and size of material that hole was placed. This tood a lot of slow increasing the size of the hole time. Also, the backplate was a different size with a two hole pattern at the top of the plate, as oppossed to the original plate with holes centered at the sides of the plate. Had to drill holes in back oven wall higher than I wanted, as the oven wall had a depression in the back wall and I could not drill at that point. By drilling holes that were higher than previous holes, there was now a 1/2" opening at the bottom of this plate. Used a hack saw and cut off a piece of the old plate to slip underneath, then screwed in the new plate, thus filling the remaining opening, and securing the additional hand made additional plate. This was a lot more than I had bargain for, and when I turned on the oven, it did not work! I re-checked the connection of the power wires to the grid element and found one of the connections to be disconnected. Reconnected this wire and everything is just ducky now.

unscrewed four screws holding part in and one by one unplugged each connector and plugged it into the new part then screwed the new part back in . i ooriginally purchased this part from ge two years ago and when it broke again i called ge. no warranty of course and the part went up over $120.00 dollars in two years. i bought this part for less than half the cost from ge and it was the exact some part . no longer dealing with ge.

pulled panel-took picture of wiring with digital camera just in case-pulled old control-screwed new on in place-switched wires from old to new-put it all back together-cooked some banana bread-oven seems a little hotter than what it reads-works like new

Removed mounting screws and element only pulled out about 2 inches. Disconnected wires and had to drill slightly bigger hole in element ends to reattach wires. Element mounting bracket was different than old element. Had to use one existing screw hole in oven back and drill a new one.

Remove the two screws holding the metal encasing to expose the controller. remove the four screws that is holding the controller in place. Discinnect the power from the controller, disconnect the other connections.. Replace the old controller with the new one, insert screws connect all wires, connect the power source..Works like a charm..

Removed 2 screws and removed the front panel. removed the controller and rewired. The wires were clearly marked and the controller was held in with four screws. Quick and easy.

Removed the screws that hold the end caps on. One on top, the other underneath with the door open. Then removed the two screws that hold the cover of the electronic controls and pulled out this panel. Removed the 4 screws that held the clock/oven module. Removed the wires in order with needle nose pliers and connected them to the corresponding connections on the new module. Weren't exactly identical, but with the magnifying glasses (presbyopia) was able to identify the correct label that matched the original connection....replace the screws back in order, started the oven...and cooked the kids a pizza.

Truned off the power took out the two screws holding the old element disconnect the power leads and put in the new element. Was great to recieve the new element in one day, the day before Xmas.