W121-E Jenn-Air Wall Oven - Instructions

Unlike many here, the oven door closed enough to come up to temperature quickly and I could not feel any heat escaping. The oven worked fine but the light stayed on because the door just wasn't snug enough. I watched the great how-to video and ordered the hinges. They arrived in two or three days! I set up a work space, cued up the video again and the new hinges were installed in just a few minutes! But the door would not close enough to turn the light off! I did some more googling around and found the magnet trick! I just happened to have the perfect size magnet from a broken souvenir magnet! and now the light stays off! I stuck the magnet (about the size of a nickel) inside the door opposite the light button. This won't help if you have serious problems with the oven door, but it works if the only problem is the light!

Removed the screws from the back of the oven to remove the damaged element; removed the electrical connectors and reattached to the new element and screwed it back in

sorry, son did job. It went like a charm. Easy, quick, and works great.Thanks

opened the door; put 12 penny nails in each hinge through the holes for it, removed screws above hinges; slid door off; laid it on a towel on the workbench; removed side/top/bottom screws and laid the outer door aside. removed the screws from the inside of the door, laid the inside glass aside, removed the glass assembly (broken), cleaned the loose glass out, laid the new glass assembly in place, replaced the panels and screws and slid the door on the hinges, removed the nails and closed the door. 35 minutes. Never did it before4. Part fit great! Thanks to partselect for having the discontinued part!

In my 26 year old oven the screws to remove the element were extremely difficult to remove, but with 6-10 applications of Liquid Wrench and brute strength we finally did. We were a bit concerned with the insulation that was protruding but used electrical tape to secure the wires to the leads for good measure. All was successfull. I love my Jenn-Aire double oven!

My husband removed the old element and replaced it with the new one. I think he used a screw driver to remove and replace. The part shipped and arrive in 5 days. Quick and easy!

The most difficult part of the repair was removing the two Phillips screws that attached the element to the back wall of the oven. With some WD40, and a hammer to tap on the screws through the screw driver (and several hours) the screws finally came loose. Once the screws were out it was a matter of removing the two wires connected to the element and reconnecting the wires to the new element. After removing the screws this job took less than 5 minutes.

Remove screws, remove old coil, place new coil, screw back in. The hardest part of this task is removing the existing screws which are most likely partially corroded and hard to move.

The heating element in our old old oven broke in half. Luckily we were able to find a replacement part (which we didn't think we would that's how old the oven is)! The part arrived within a couple of days, my husband removed the old element (toughest part was getting the two old screws unscrewed) plugged in the new one and he was done. Took about 5 minutes! I turned on the over to test it was connect properly and it started heating up right away! We are VERY happy !! :o)

Removed the door by unscrewing two screws holding it to the springs. Then I placed the door face down on a counter top. I removed the screws from each layer of the door and turned each layer over and laid it beside the door. Took care to support glass so it did not fall out and break. When I got to the layer where the seal was, I removed the old seal and replaced it with the new one. Then, I replaced each layer in reverse order. You have to be careful when replacing the layer that goes over the seal that the seal remains in the right place. It has a tendency to slip out of place, so check it before tightening screws. To place the door back on the spring loaded handles, prop the handles open a ways with screw driver handles. This provides a gap so that the door will slip on easily

We took the door off, you have to be careful of the hinges popping back. We put small screwdrivers on each side and held the hinges out, this made the door easy to just stand up and slide back on the hinges. The glass replacement was simple just a few screws. We spent $127.00 on the part and shipping and a new wall oven would have cost us $1500.00. Thanks for making this part available.

Received the part within 10 days and installed in less than 60 seconds.

pulled one off and pushed the other one on.fino

I followed the online video at Jennair.com. The repair was easy and I saved quite a bit of money. I was quoted a price of $534.00 to replace the door hinges, I did it for $96.00 including overnight shipping chargers. I am a very happy lady.

Removed racks from oven, unscrewed two screws holding old element in place with philips head screw driver from the back wall of oven. Carefully pulled element from oven to expose connecting wires and then pulled two wires loose from old element. Reconnected wires on new element and carefully reinstalled element to rear of oven interior with two screws removed from original element.