W30400W Jenn-Air Wall Oven - Instructions

My microwave is stacked on this stove. I had to pull cover off to slide part off. screws were a snap. only problem was the slip catches on the ribon strips. Sperating with flat head was scary but worked fine.

Cut of electricity. Opened the oven door and removed some screw that were over the door that let a plate be removed. Then that let the part drop down that was holding the clock. I removed 2 screws that was holding the clock in place, unplugged the 3 connectors that feed the clock, attached the 2 screws back in that held the clock, put the part back up in place, added the plate and was done. Turned the power back on. I was delighted when I saw the clock light on. Easy to install.

I first turned the power off to the stove at the junction box. Removed the control panel that contained the clock assembly by removing 4 phillips head screws. While my wife held the control panel, I disconnected the two pin connectors and one ribbon connector attached to the clock. I then removed the two phillips screws holding the clock assembly in place. To disconnect the ribbon connector, press the release buttons on the side in and the center loosens and pulls out, releasing the ribbon. There are two plastic tabs that fit into two guide holes on the ribbon. The best part of this is that 6 months ago, two number keys and the timer button had quit functioning and I thought I was going to have to replace the touch panel also. Apparently it was a problem with the circuit board on the clock assembly because everything works now! My ife is very happy!

Once the display became too dim to read, I removed the front panel to determine how to access the piece and to check part numbers so that I could order the proper piece. Once the part arrived, being familiar with the disassembly, it was simple enough to replace the part quickly. The part came out with two screws and the connections were standard electronic multi plug, making the replacement simple. When we turned the power to the unit on, it worked first time.

Loosened the contol panel until I was able to get to the Digital Display board.
Removed the three cables and the screws that held the display unit to the control panel.
Reversed the procedure to instll new digital clock display unit.

This is the second clock I have had to put in this unit in about that many years. The first time I disassembled far to many things. This time I knew to only unscrew the front panel and side triangle plates. The process was much faster the second time. I hope this is not a chronic problem though.

Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off) now turned off. That's a lot of things working better for less than $50!

I replaced the heating element but that didn’t help. So then I replaced the oven sensor and that didn’t work either. Both were pretty easy to do but I’ve now spend $170 and my oven still isn’t working. I called number listed and got a recording that all agents were busy and there was a high call volume so I can’t get any help.

My daughter & I followed the instructions in your video and had fun repairing the door. The video showed exactly how to do the repair. I hope I don't need any appliance parts very soon but I will certainly pull up your web site if I do. Thanks for an excellent instruction video.

John - Hot Springs Village, AR

installed part,turned unit on-temp still cold. reset digital control, up 35 degrees, still cold. un-plugged unit,re-connect after 10 min. still cold.

Extremely simple repair to make. Move stove away from wall and disconnect power. Remove the oven racks. Remove the rear sheet metal panel covering the wiring harnesses. Caution: Sharp edges and corners on sheet metal.Sensor is located in upper left corner on rear oven wall. Using a long-shafted #2 Philips screwdriver, remove the two Philips head screws and gently pull the sensor 1" away from the oven wall. At this point, it will help to have an assist from someone while you are behind the range. Have the assistant gently tug on the sensor while you watch for wires moving on the rear of the range. After locating the sensor wires, gently disconnect the plastic connector clip. Note: plastic connectors become brittle with age and exposure to heat Move to front of range and gently remove sensor from rear wall by pulling the wiring through the oven wall. Before inserting the new sensor wire through the oven wall, "dry fit" the wiring connectors to see that the new sensor is a correct connection. Make connection, and secure the sensor to the rear oven wall with the two screws. Install racks, reinstall rear sheet metal panel, and connect the power. Set the oven baking temperature to a moderately low temp, 300 - 350 deg. to test the new sensor.

I removed the two mounting screws and pulled the harness through the opening unsnapped the sensor from the harness and installed the new sensor i didn't have to used the adapters the new sensor fitted

1) Unplug Appliance
2) Remove stove front (4 hex-head screws)
(Note: support front while removing screws)
3) disconnect (3) wiring harnesses
(Note: exercise care when revoving "data bus", release with small "dogs" on each side of plug.)
4) Remove Clock assembly (2 hex-head screws)
5) Replace Clock assembly (2 hex-head screws)
6) Reconnect (3) wiring harnesses (reseat bus plug dogs)
7) Reattach stove front (4 hex-head screws)
8) Plug appliance in to power outlet

Note: Before the repair, all functions and displays worked just fine, they just weren't illuminated so you couldn't read any thing. It really steams me that I had to pay $141 to replace a 50 cent light.

Remove four screws behind control knobs. Remove four hex nuts under control panel (open oven door to locate). Pull control panel down and out. Remove two hex nuts holding clock assembly. Remove three wire connectors on the old clock assembly and carefully insert on new clock assembly. Reverse instructions to re-assemble. It's a breeze to do! Took longer to get my tool box than the time it took to replace the clock assembly.

I removed the three screws that was on top of the display enclosure. I then removed the four screws on the bottom of the display enclosure.

I unplugged the two connectors going to the old enclosure and removed the enclosure to the kitchen table. I then pressed the two locks on the ribbon cable lock and pulled up on the ribbon cable lock. I was unsure how to do this, but if you press the two tabs and slightly pull up on the lock, the ribbon cable will come free.

I then removed the four screws holding on the old display and put the new part in. Fastened with the four screws and connected the ribbon cable, squeezing tabs and raising the black lock, inserting ribbon cable and pressing down to lock in place.

I then took the enclosure to the oven, connected the other two sets of wires and mounted the enclosure with the three upper scres and four bottom screws. Took me about 15 minutes. My $148 PartsSelect part was $267 locally.