W30400W Jenn-Air Wall Oven - Instructions

First I took the screws off of the top hood which can be found right underneatch, this allowed me to access the panel bolts and unscreww them. We then got it far enough so that we could easily replace the old with the new and plug things back in and we were good to go. I am not sure but we must have save hundreds of dollars in a repairman.. This website is awesome..

I looked at the schematic from PartsSelect, undid the 8 screws and replaced the clock assembly. I probably saved $200 on labor doing it myself. I had the clock repaired in 30 minutes.

I first turned off the circuit breaker for the range. I then I removed the four hex screws from the underside of the panel and then dropped the panel to expose the clock assembly. I then removed the two screws holding it in place, disconnected the cables and removed the old unit. I then reversed the procedure to install the new unit. I next turned on the circuit breaker restoring power to the range. And like magic I once again had light. I know I must have made by Daddy proud. I should have done it sooner. Thank you for making it so easy by sharing the "how to's" with me. It was especially helpful to have the model number.

Turn off power to the stove. Pop off the burner knobs and remove the screws attaching the controls to the front panel. Open the oven door and remove the four screws attaching the panel to the oven frame. The panel slides down giving easy access to the circuit board. Remove the two connectors and the ribbon cable attached to the board. There are small clips on the side of the ribbon cable connector that release the ribbon cable. Unscrew the board and install new board. Reattach the cables, put the panel back in place and attach. Reattach the burner controls to the panel, pop the knobs back on, power the stove back on, put on a pair of sunglasses to view the now blazingly bright display and admire your work.

As described by many others before. Turned off the power at the circuit breaker panel for the house. Unscrewed the front panel, disconnected the three connections to the old assembly and unscrewed the assembly.

Cleaned a few pieces then screwed in an connected the new assembly, put it all back together, turned on the power, said a prayer and IT WORKED!

Open oven door
Remove two sets of four screws underneath the LED display
Remove stove handles (pull off easily - no tools needed)
Lower flat plate width of oven and about two inches deep should be able to drop out from under the clock display.
Remove face plate over clock.
Unscrew four screws holding clock unit down.
Undo two electric connectors and the thin ribbon connector - the thin ribbon connector is different - the ribbon comes loose and the black plastic connector stays in place on the board.
Press the thin ribbon connector ends inward and pull up to detan ribbon on old one and then to insert ribbon on new one.
Reverse the rest.
Not too bad!

1. Removed knobs and front panel. Disconnect wiring.
2. Order part and installed. Done

I first turned the breaker off. Then removed the screws under the display with the oven door open. Then removed the side screws. Then removed the trim kit for the microwave which exposed 3 more screws. The middle one with the Micro Door open. The complete display panel then was removable. I took a digital picture of the 2 wire and 1 ribbon connectiors (I know-anal). Then removed the 2 wire groups-struggled somewhat with the ribbon connector until I realized by trial & Error that the 2 little tabs on the sides only pull upward, releasing the ribbon. Removed 4 nutdriver screws to remove old display-installed new one in reverse fashion. Then I CLEANED everything I could reach it was so dirty! (I live in the desert,duh!) I just paid great attention to how it came apart and it was relatively easy. The best part is that I didn't have to remove the Oven/Microwave unit to do the repair.The new part works perfectly, thanks!

Unplugged the range, removed screws holding the old sensor. When I pulled it out, the wire connecting to the sensor was completely broken through,therefore I could not just pull the wire to get to the connector. Unscrewed one side of back panel to access the connector. Pushed the connector and wire of the new sensor through the hole ( and behind the insulation), disconnected the old sensor and connected the new one. Re screwed the new connector in place plus rescrewed the back panel. Plugged the range in and - Viola! Everything now works like a charm and I have my oven back. Easy-Peasy. Oh - I am an older female with very limited DYI experience. I just saved myself $650.00!

Removed screws on face plate, disconnected wires, placed on counter, removed hex head screws. Removed one end of electric type circutry, replaced with new part and reassembled.

My wife help take the door off. It was a little heavy . The door came apart very easy and went back the same way.We save over $300 by doing it our selfs.

Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.

I installed the new oven sensor but the problem continued. So I ordered a new relay board and installed it. Still no luck. So I pulled the new board back out and started trouble shooting it using my electronic background. I discovered the new board was using a pin for L2 that had no exit on the backplane, so I removed it and installed it where I believed it should go. Reinstalled the power relay board and presto. My oven is working lie a champ. Louis

Turned off the breaker. Removed the screws under the front panel and eight screws behind the burner controls (two each). I then slid out the panel and laid it flat on top of the stove. Removed the three connectors. Most difficult was the ribbon connector: Squeeze the clips at each end and slide the top half of the connector up. Then the ribbon slides out (practice on the new part). Only two screws held the assembly in. Reverse the process with the new assembly. Worked great!

piece of cake KILL POWER AT BREAKER BOX. Remove burner knobs exposing 4 screws. Open oven door exposing 4 philips srews, four 1/4 hex head screws, and 2 philps screws for end caps. Had to pull out range about an inch (less) away from countertop. Remove screws. Move end caps away from face plate.Pull out face plate. Pull down / out bottom plate to expose Assembly. Unclip wire connection, carefully pull out ribbon connection. Remove 2 screws. Install in reverse.