JJW9530BAW Jenn-Air Wall Oven - Instructions

the glass front that houses the clock has four screw just above the door. Open the door to access the screws. Once the screws are out,
the glass front can be lifted up off the oven.
Instead of replacing the housing and the circuit board I removed the board from the housing and
and it snaps back into the old housing.

Remove trim piece from microwave above oven.
Remove 5 screws from inside oven below the display and control module
Lift out module and unplug three wire harnesses
Remove display and PCB from module.
Install in reverse

After trying to set the bake temp after the self cleaning, it would not heat up. I Googled the model number,selected your link because it mentioned my symptom,and said usually it is the temp sensor in the oven that gets damaged by the high self cleaning heat. Your site had a place to enter my model number. You provided a great exploded view of the parts, showing me my sensor,then you provided the part number of the kit i needed,and filled out the order form with payment method. Less than a week later I got my part with instructions. Your video showed me the two screws I remove from the front ,and I pulled the old part out and uplugged it's connector. Replacement was easy, and oven was fixed! Thank you for a great site! You held my hand through it all!

Flipped off breaker and removed oven door and pulled built in stove out so the back panel could be removed. Unplugged the sensor then removed the two screws securing the old sensor inside the oven and installed new sensor. Put stove back together and installed back into counter top, re-installed oven door, flipped on the breaker and oven works like new.

Replaced the long Oven Sensor but have not resolved the root problem. Oven still will not reach required temperature. Bottom element becomes red hot, but turns off and will not start again.

Had to remove oven from mounting cabinet to get to the back since the wire lenght to the conector was to short to come through the mounting hole.
Other than that the repair was straight forward. 4 screws to dismount the Oven from cabinet, 2 screws to remove Sensor and 3 srews to open the back of the oven once out in the open. New cable adapter that came with the new sensor was needed in my case.

Removed the oven from the wall. Removed back cover and unplugged sensor from the harness. Remove and replace sensor from inside the oven. Reconnect harness and reinstall back cover. Secure oven back into the wall.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

This is a straight forward part replacement. You will need a phillips screw driver, a hex nut driver, a towel folded lengthwise, and a flash light. A second person's hands are helpful, but not necessary if you have a folded towel ready to use. First, shut off the electricity to the oven at the circuit breaker. Then open the oven door and remove the four phillips head screws under the oven control panel. The panel will then lift up and out easily. Highly recommended: have a second person present to help hold the control panel securely while you remove the three wire cable plugs from the existing electronic clock assembly to avoid scratching the plastic surface of the control panel against the sheet metal brackets that hold it in place. Alternatively, have a folded towel handy so that you may rest the control panel face down on the sheet metal brackets from which it was removed with the folded towel protecting it from being scratched by the metal brackets. Once the wire cable plugs have been removed, the control panel may be moved to a safer location with a soft surface (on a towel or other protective surface) to remove the four hex screws that hold the clock assembly to the control panel. Substitute the new part and replace the hex screws to hold in place. Attach the three wire cables to the new clock assembly, set the control panel back into it's brackets, and replace the four phillips screws to hold it firmly into place. Reset the circuit breaker to the oven. Reset the clock time, which will be 15 to 30 minutes slow (the time you had the power off). Done!

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Very easy to replace. open oven door,
remove four screws holding oven control
cover, remove 4 1/2 in screws holding
display unit with a nut wrench, unplug
three connectors. intall new unit, replug
connectors and replace screw in reverse
order.

We followed the 63 year old lady's repair directions found on this website and were able to install the new display board in less than 15 minutes. As she said, it was really easy!

I unscrewed the cover on the oven. Used a socket to remove the electronic circuit board and unplug the electrical connectors. Then I plugged the new board in and reattached it.

Some of the connector prongs got bent in shipping I guess but I was able to straighten them.

I have a stacked microwave and oven. Removing the oven control panel was easy, removing the circuit board was easy, Replacing the wiring strips and board was easy. Reataching the control panel with the four screws was the hardest part., Gotta wirk upside down!! Saved about $200 doing it myself.

1. Remove 4 screws at the bottom of the control panel (above oven door) that hold it in place.
2. Pull the control panel away from oven and lift to remove.
3. Unplug two wire connectors to remove panel from oven.
4. Unplug two wire connectors from the clock panel. Used a putty knife to disengage the connector locking mechanism.
5. Remove 4 screws holding clock in place.
6-10. Installed new clock in reverse order of removal.