S176B Jenn-Air Wall Oven - Instructions

Opened the oven door and locked the spring hinges in the opened position with two 10p nails. Removed the oven door. I dismantled the component parts of the door. I then removed and replaced the broken glass unit,reassembled the door, slid the door onto the hinges, tightened two screws to lock the door in place, removed the 10p nails, closed the door----- and that was it. Less than one hour. The job was accomplished using only a Phillips screwdriver.

Using exploded view and previous customers' comments, I disassembled the door. It was primarily a matter of finding all the screws. I recommend taking the door off first (I didn't), but watch your fingers. The hinges have very, very strong springs and you can hurt your or your helper's fingers if you're not prepared. The hardest part was keeping all the insulation in place while your're installing the assembly. I also replaced the gasket. That takes four hands, two to hold the gasket in place and two to reinstall the window assembly. To put the door back on the hinges, I pulled them out from the door at a 45-degree angle (takes some effort), put screwdrivers through holes in the hinges, and guided (with help) the door back on.

I didn't. Don't know how to get to light bulb to change it for this specific model

Motor (Blower Motor Kit) Part Number: PS1569907
No instructions are included in the package from PartSelect. Disassembly from the main housing was relatively simple. I found that paying VERY careful attention to how the original motor was wired and mounted would pay off in correct re-assembly, conquering motor vibration and rubbing. Most of my project time was spent cleaning the rotating blade wheel from 20 years of grease build-up. On tools, I would have appreciated the inclusion, or availability as an accessory, of a long-stem correct-size allen wrench (used in removal of the fan blade wheel.) The job went well, and probably saved me $200 in service call and labor.

First I removed the two screws that held the old element in place. Then I pulled the element out about 5 inches so I could reach and pull off the wire clips from the old element. I then attached the wire clips onto the new element and pushed back the wires into the insulated area and when the back plate matched up to the screw holes, I re-inserted the screws and tighten them down. The oven works great.

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

removed 4 screws holding burner controls. removed wires off old and placed on new burner control. very pleased with quick shippig of part. two days and range was as good as new. excellent company to buy from

I slide the range out and unplugged it from the outlet. I removed the back of the oven ( 8 screws ) using a cordless drill and phillips bit then with a phillips screwdriver I removed the oven sensor (2 screws) then I installed the new sensor , reinstalled the oven back , plugged the range in , slide it back into place and that was it. This repair took about 10 mins and the oven works perfectly. Thanks !

Took the (6) screws holding the top of the stove out, then removed the switch screws(2). Then lifted the top, so as I could reach and get at the switch. And then I repeated the above. It was alot easier the second time. Duh I erred the first time and replaced the wrong one and before I relized it, I opened the switch to check out. All in all. I still got satisfaction from doing it myself. Thanks Parts Select

- the fan/light switch was still functioning, but it fell into the cavity underneath, after years of use, heat and grease caused it to weaken.
- 4 wires came off the old switch, and went on the new one with ease.
- the only complication was in getting the clips off of the old ones, and getting the new clips onto the new one. otherwise, a piece of cake.

blower wheel was caked with dried grease clumps; replaced blower wheel, urethan foam and 3 motor isolators; blower/fan no longer vibrating cooktop.

I removed the 4 screws that held on the front panel as well as the knob of the defective switch. With the panel free, I pulled the wire connections from the rear of the switch with needle-nose pliers. I then removed the 2 screws which secured the switch and removed it. I then reversed the process with the new switch. It could not have been easier.

First we removed the two screws that hold the element in place. After pulling it from the back of the oven we did not realize that the clips that held the wires could be slipped off the 'tongues' of the element. Therefor we thought we had to cut the wires - which we did. After realizing that the clips came off, we went to the store and bought a box of new clips, stripped a small portion of the plastic on the wire to expose the wire and put it in the new clips and crimped them. Then slipped the new clips onto the new element, replaced it and put the old screws back. You wouldn't need to buy new clips (not expensive) if you know ahead that they can be removed from the old element and slipped onto the new one. We were amazed at how quickly the element arrived in the mail. Have bookmarked this sight for future repairs.

First I turned off the circuit breaker at the control panel to my Jenn-Air stove-top. At 220-volts, don't take any chances with electricity!

Then I removed two screws that hold the burner switch panel in place and lifted up the panel to expose the wires that are connected to all 4 of the burner switches, the exhaust fan and pilot lights that indicate if a burner is turned on.

I used a circuit tester to determine that the power was indeed off to the switches. Again, it is extremely important to respect 220-volts of electricity.

I ensured that all of the wires were already labeled the same as the terminal connections on the switch (i.e. H-1, H-2, P, etc.). If they are not, label them yourself with masking tape around each wire. Then I removed each of the wires connected to the burned out switch with a pair of needle-nose pliers.

Next I removed the two screws attaching the burner switch to the panel.

To install the new switch, repeat all of these directions in reverse, making sure to attach each labeled wire to the correct terminal on the burner switch.

Turn the circuit back on at the circuit breaker. Then test the burner switch and see if the burner heats up. Hopefully, you'll be cooking in no time...............

It would have been nice if basic instructions were supplied ( eg. how to remove switch panel ) but it went rather smoothly.
First killed power the electric stove.
I then removed the screws from the bottom of the panel and then pried the top of the control panel down and then out. I copied the positioning and wire colors.Removed wires from prongs, removed the two screws, replaced old switch with new one .