W206B-C Jenn-Air Wall Oven - Instructions

Removing the oven door and several layers of metal to get to the seal, is a fairly easy process. Our door had three different fasteners, torx head screws to remove the door, a very small flat head screwdriver to remove the chrome door trim screws, and a nut driver to remove the inner panels and glass. The replacement seal is over-large and must be trimmed. Care should be taken when fitting the integrated wire. Bending at the corners only, makes assembly much easier. Reassembly is the reverse of diassembly. Care must be taken that the seal wire hasn't popped out of it's seat when the cover is installed. This is the most time-consuming and frustrating part of the repair. Patience is paramount to get a good fit. Because I had made an odd bend in it, about one inch of wire was not properly seated after the cover was seated and tightened down. I was able to gently squeeze it into the seat with a flat tip screwdriver without removing any screws. The final problem area is reinstalling the door. Although two people would be helpful to accomplish this Task, I was able to accomplish it with the aid of a three foot piece of 2x4. By wedging the piece of lumber behind both hinges, they were held open under tension to allow slipping the door on. Once partially installed, the 2x4 can be removed and the door seated. Hope this helps.

I raised the top of my Whirlpool Continuous Cleaning Canning Oven, then had to unscrew 3 screws and a lock nut, then raise top about 4 inches, so I could put my hand inside to unplug the wires to the switch, and push it through the hole in front, of oven. Then put the new switch through hole and plug in new switch. Then screw down top; and close lid. Part #866294

Removed the door removed 2 inner panels Installed and reassembled A Cake Walk NOTE be careful not to strip threads

Removed door (that was the most difficult part)
Took out lots of screws to disassemble
Cleaned all the components that were now exposed
Put new seal in place
Put parts back together with screws
Put oven door back
Excellent!!

It would have been a very easy job if the one wire had not fallen inot the back. I could not reach it and fried to figure out how to get in the back to no avail. Finally I took a piece of wire coat hangerm and bent it and then fished it out. The packing around the hole compressed while I was trying to get the wire and I thought I wpuld have to replace it, but overnight it resumed its original size. It should have probably taken less than thirty minutes.

Removed the original element with a screwdriver and disconnected the 2 wires, it took about 2 minutes. Got online with PartSelect and easily matched a replacement part. Ordered the part and received it within a couple of days. Very impressed with the ease and quickness of the order processing and shipping. Took the new element and connected the wires, screwed the 2 screws back in, it took about 2 minutes. Turned on the oven to check and everything worked perfectly. Very happy with the overall experience with PartSelect. Thanks!

First, I tripped the oven circuit breaker. Then I removed the two screws that hold the element in place. Then I pulled the element out about 5 inches and disconnected the two wires. At first, I had to figure out how the wires would disconnect. Once I removed the heating element, I reversed the procedure, tightened the screws, reset the circuit breaker, and set the oven to bake. The element began to function, and I knew Imy efforts were successful.

repair was simple two screws

Checked the element to see if it was open or no
resistance, it was open
e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)

Received the new one. Installed it in 15 minutes. Thanks for the fast service.I will buy from you guys the next time I need a part ! Thank You, Henry

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

takes two people to put the oven door back in place but otherwise very simple as long as you keep all your screws and pads in place

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

ordered new broiler pan

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.