JJW8530BCW Jenn-Air Wall Oven - Instructions

Replacing the electronic Clock Assembly was a piece of cake - just as earlier DIYers had experienced.

The door hinges were not any harder to replace, but it does not affect the behavior of the door. The light stays on unless we keep the door closed with a hook and anchor ( bent piece of metal and a wooden wedge). Not pretty, but effective. Obviously a design flaw... keeping door closed in this way forces all airflow to top and has melted the paint into a wrinkled surface. We had a service person replace the gasket seal and hinges before, but the problem still persists. I did discover that soaking the light cover in a cola drink overnight did a splendid job of cleaning off the gunk.

Same as the others to get to the bad clock. My old part was a circuit board which was made with white material and manufactured by RoberShaw. The new one was on a green material and by another manufacture. The new one felt a little heavier and look like there were more componets on it. However the plug-in connections and the mounting method was exactly the same. Before reassembly, I used a long handled brush to clean out most of the baking gunk that
had accumulated in this area and I used a clean wipeing cloth to clean the inside glass for the display. The best thing about this was the part came on the Thursday before
Hollowee, I installed it as soon as I got home from work. My wife started baking cookies and cup cakes for trick or
treat and all is well.

First I called a repairman and left a message. That was 3 weeks ago. So, I 'googled' the error message and determined what part I thought I needed. Ordered the part on Wednesday evening and it was there when I got home from work on Friday. I unpacked the part, got a phillips screwdriver and then watched the repair video on your website. About 20 minutes later I pushed my stove back in place and the flashing said 'set time'. Then I checked both ovens, and have since used both, and everything works!!

Spoke to your very helpful staff, who advised me that a likely problem was the oven sensor. I took a chance and ordered the part, which came promptly. Your service video for the part was most helpful in my decision to try the part. Installation was a breeze, but it was the oven controller board that had failed and not the oven sensor. That called for a service professional, who ultimately fixed the problem. Your service though, was excellent and I would highly recommend you to others.

Ordered the part. when it arrived-quite speedily, I just unpacked it and put the cotton gasket around the glass and screwed it to the proper place in the oven. Very easy.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

I removed the four screws holding the control panel to the oven. I then lifted off the panel and rested it on the the oven rack which I set in the top position and pulled out about a foot. Next, I removed the three plug in cables and removed the two screws from the frame that was holding the clock assembly in place. I put in the new part and reversed the procedure. Total time to replace part was six minutes.

My son removed the switch panel and unpluged
the switch. Then he replaced it with the new
switch fasten back the panel and turned the
power back on and everythiing worked fine.

I switched the oven sensor easily enough, but it did not remedy the problem, so we are in the process of replacing the oven since it's about 20 yrs. old.

Removed the display panel with 4 screws. Then disconnected the wires and plugged in the new display panel. Turned on the power again and it was brand new.

I contacted a local appliance repair store who didn't know what I was talking about. I looked online and the store called me back to tell me the part would probably be $75.00. I took the broken part out of the door frame and found the exact part online at your site, and ordered it for $14.00. Received the part within 2 days and put it in in 10 minutes.

I took out 4 screws under the display panel. Lifted the panel up and off the oven. It was connected to 3 or 4 plugs on the control panel. I unplugged them and un screwed the control panel and screwwd the new panel in replugged the wires into the panel. walla it worked.

I watched a You Tube video,removed and dismantled the door, installed the new hinge. I forgot to remove the small pin which is similar to a rivet. When I tried to close the door it bent. Eventually, I remembered the shipping pin and pulled it out with any damage. Believe it or not, I had read about the shipping pin on customer comments on PartsSelect...Good luck, it is relatively easy!

I took the broiler pan out of the shipping container and put it in the oven.

I removed two screws holding the element in place. Carefully pulled the element from its mounting throught insulation to expose the two wires connected by electric wire clips. I removed the clips and searched the part online using google. Part Select was provided as the top source. I ordered the part and it was delivered in two days. Taking care to thread the connection through the insulation, I was pleased to have installed it in about 5 minutes. All tools were still out and ready for use. Thank you for your service