W30400PC Jenn-Air Wall Oven - Instructions

The expert said to replace the clock control and linked to the replacement part. The part was promptly shipped. The only difficult part of the repair turned out to be the removal of the ribbon from the old controller. I noted the tabs on the side of the ribbon receptacle and expected the ribbon to release when these were pushed in. What was actually needed was to not only push in but also to pull upward on the tabs in order to release the ribbon. That was not obvious and it took me a while to get the ribbon released.

unplugged oven. removed 2 screws that hold the sensor in place, then removed the dozen or so screws that hold on the rear panel, unplugged sensor and fed wire through insulation. identified and installed correct harness adapter then fed new wire and connecter through insulation and connected to adapter. installed sensor retaining screws.plugged oven back in and tested function.no dice. unplugged oven once again. removed oven control panel and upon inspection of printed circuit board discovered 3 solder joints had failed. dang. resoldered failed joints and also sweetened up a few others that looked suspect. reinstalled controller, replaced all retaining hardware, and plugged in the oven. tah-dah!! works like a charm now. moral of the story is check the pc board first and save $50 for unneeded pats!!! or buy the controller from parts direct for $260ish. btw a roll of solder and soldering iron from an auto parts store cost around $10, learned to solder on you-tube $0. amazing all the home appliances yo can fix if you're not afraid to take a few screws out and poke around a bit. CHEERS!

First I turned the power off to the stove at the breaker box. I opened the oven door and took off the four hex head screws holding the face panel on. There are four philips screws holding a trim piece on the panel that does not need to be removed and the two end caps do not need to be removed either. I pulled the panel out and tipped it up so I could access the clock display unit. There are two wiring harness clips that unplugged very easily. The ribbon connector is a little more tricky. You have to slide up two clips on the end and then slide up a section going across the ribbon. It's very easy, just don't try to pull the ribbon out without undoing the clips. The display unit was held on with two hex head screws. I removed them, attatched the new one and put it back together. I then turned the oven back on to see if it worked. The display worked perfectly but, the oven would still not get hot on bake. I turned the breaker off again and removed the shelves in the oven. I then removed the two phillips screws holding the bottom bake burner in and pulled it out until I could access the clips. I pulled off the clips and checked the burner for continuity. There was none so I ordered a new bake burner. The new burner showed up the next day and I hooked it up in about 5 minutes. The oven works great and I couldn't be happier with the experience I had with partselect.com

Had estimates of $ 500.00+ to replace clock assembly. Purchased it at parts select for approx $ 200.00 and put it in myself. Will pocket the $ 300.00. Thanks. Turn breaker to stove off. Removed four screws underneath front panel. Must open oven door to access screws. Tilted the panel out from the bottom allowing the top of the panel to come out. Had to remove the two knobs on either side of the clock along with the clock knobs. When the two knobs on the side are removed it releases the mounting brackets for the clock inside the panel. Replaced clock assembly wires one at a time. Reassembled in reverse procedure.

The range had to be pulled away from the wall to access all of the retaining screws. Once all the screws were removed, the top was easily lifted away, allowing easy access to the clock unit. Three wire connectors were also easily disconnected, and the clock was secured by only two accessible screws. Reassembly was straight-forward; the only difficult, and time-consuming part was sliding the range back against the wall, as tolerances were tight. The repair took 45-60 minutes and the clock shines brightly!

Turned off the breaker to the stove and removed the 4 screws under the control panel. The trim strip and the end caps did not have to be removed. The control panel was lowered just enough to clear the upper edge and then tilted forward so the connectors could be disconnected. Two screws holding the display in place were removed and the new display swapped out. Reassembly was disassembly in reverse. (My wife appreciates having a bright display again.)

I had a service guy come in and he told me the repair would be $550.00. I asked for a part list and did it myself. You guys saved me hundreds of dollars.

Took door off oven (easy - 2 screws) then toolk door apart to install new glass - also easy and only about 6 screws and removak of 4 nuts involved. Service from PartsSelect was excellent and deklivery was fast. Would use them again.

Irwin C. Cobane

The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not look for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine.
Mike

We simply removed the front knobs, the 8 screws underneath the front panel and dropped down the control panel. We removed two screws holding the assembly and removed the ribbon cable and the two other connectors. We put the new one in and reattached all the cables and reassembled and it worked great. Took 15 - 20 minutes.

took out the old dome cover and replaced it with a new one by unscrewing and replaced the new one and a fiberglass gasket. simple.

Very simple. A few screws removed, disconnected a few wires, reattached the wires, put back the screws all without a single cuss word

Ordered the part. when it arrived-quite speedily, I just unpacked it and put the cotton gasket around the glass and screwed it to the proper place in the oven. Very easy.

I switched the oven sensor easily enough, but it did not remedy the problem, so we are in the process of replacing the oven since it's about 20 yrs. old.

We followed the DIY stories of others (like this one):

Turned off the breaker to the stove and removed the 4 screws under the control panel. The trim strip and the end caps did not have to be removed. The control panel was lowered just enough to clear the upper edge and then tilted forward so the connectors could be disconnected. Two screws holding the display in place were removed and the new display swapped out. Reassembly was disassembly in reverse.
Had to be gentle about unplugging and plugging in the ribbon cable.
Very happy with PartSelect product, delivery and website help.