Models > W214 > Instructions

W214 Jenn-Air Wall Oven - Instructions

Jump to:

All Instructions for the W214

Customer:: LARRY from MCLOUTH, KS
Parts Used:: WPY702338
Difficulty Level:: A Bit Difficult
Total Repair Time:: 1- 2 hours
Tools:: Nutdriver, Pliers, Screw drivers

Biggest problem was trying to get the two hinges to open up so that the door could be reinstalled to the hinges.

The basic replacement of the bad seal went fairly well. Just had to follow the other guidance and pay close attention to the correct sequence so that the door goes back together as it should be. The only real difficult part was when attempting to hold the hinge downward so that the door could be properly placed back on the hinges. After closer examination I discovered that there were two holes in each of the hinges that when they were opened all the way that the holes lined up and I cut off two nails approx 2 inches long and then once I was able to pry the two hinges all the way opened and then I used them to slip in through the two holes and they worked just fine and they held the door open, until the door could be re-installed. Once installed the nail/pins could be easily removed with some needle nose pliers.

Was this instruction helpful to you?

Customer:: Ginger from Waterville, OH
Parts Used:: WPY702338, WP7711P466-60
Difficulty Level:: A Bit Difficult
Total Repair Time:: 1- 2 hours

Missing nobs...I installed them!! Ha...It took time to take the oven door appart for the seal.but no problem. Door latch required the drop in oven to be pulled out. Need some he men for that. If done within 90 days...no extra charge.

Called Sears as they will install parts you have purchased. I am a 67 yr. old woman. Already had the new element. Cut my cost by almost 2/3rds as other companies charged a fortune to guarantee their own work with their own parts..Which they probably get from you!!!

Was this instruction helpful to you?

Customer:: Romeo from Suffolk, VA
Parts Used:: WPY703499, WP703502
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

two from knobs were so old from constant washing you could not see the lettering on the knobs.

pulled one off and pushed the other one on.fino

Was this instruction helpful to you?

Customer:: Grant from Alexandria, VA
Parts Used:: 8009
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Light bulb failure

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Was this instruction helpful to you?

Customer:: Mark from Niagara falls, NY
Parts Used:: WPY703499, WP703502
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Old knobs worn out

The new knobs were simply pressed in placed on the existing shaft, perfect fit, looks just like new, yet 24 years old. Would tell family and friends to shop for parts at Part Select.

Was this instruction helpful to you?

Customer:: Rebecca from Spartanburg, SC
Parts Used:: WPY703499
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Cleaned stove. When temperature knob was cleaned, temperature settings were wiped clean.

Received the part within 10 days and installed in less than 60 seconds.

Was this instruction helpful to you?

Customer:: Mary from Apple Valley, CA
Parts Used:: WPY702338
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

Needed a new oven door seal

Left door attached to range. Took out all screws on door to get to the door seal. Cleaned parts as I went. Took out old seal and laid new seal in. Had to get two more hands to hold the parts and glass together while screwing it back together. Only hard part was remembering which screws went where. Looks and works like new. So glad I did it, as it has needed it for a long time. Easy even for a 70 year old female. PartSelect had the best price even with shipping. Thanks

Was this instruction helpful to you?

Customer:: peter from springfield, PA
Parts Used:: WPY04100514
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver

Failed Broiler element

Removed back of stove - 4 screws on top, 3 underneath. Unplugged wires from element. Removed element - 2 screws in front and 2 in the back. Installed new element, plugged wires back in, reinstalled back panel.

Was this instruction helpful to you?

Customer:: larry from Camp Hill, PA
Parts Used:: WP5700M600-60
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

oven door glass shattered during cleaning

opened the door; put 12 penny nails in each hinge through the holes for it, removed screws above hinges; slid door off; laid it on a towel on the workbench; removed side/top/bottom screws and laid the outer door aside. removed the screws from the inside of the door, laid the inside glass aside, removed the glass assembly (broken), cleaned the loose glass out, laid the new glass assembly in place, replaced the panels and screws and slid the door on the hinges, removed the nails and closed the door. 35 minutes. Never did it before4. Part fit great! Thanks to partselect for having the discontinued part!

Was this instruction helpful to you?

Customer:: Vonnie from Indian Rocks Beach, FL
Parts Used:: WP5700M600-60
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

glass in oven door was broken

We took the door off, you have to be careful of the hinges popping back. We put small screwdrivers on each side and held the hinges out, this made the door easy to just stand up and slide back on the hinges. The glass replacement was simple just a few screws. We spent $127.00 on the part and shipping and a new wall oven would have cost us $1500.00. Thanks for making this part available.

Was this instruction helpful to you?

Customer:: Vern from Sugar Land, TX
Parts Used:: WP701650
Difficulty Level:: A Bit Difficult
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Door seals worn

Removed the door by unscrewing two screws holding it to the springs. Then I placed the door face down on a counter top. I removed the screws from each layer of the door and turned each layer over and laid it beside the door. Took care to support glass so it did not fall out and break. When I got to the layer where the seal was, I removed the old seal and replaced it with the new one. Then, I replaced each layer in reverse order. You have to be careful when replacing the layer that goes over the seal that the seal remains in the right place. It has a tendency to slip out of place, so check it before tightening screws. To place the door back on the spring loaded handles, prop the handles open a ways with screw driver handles. This provides a gap so that the door will slip on easily

Was this instruction helpful to you?

Customer:: Christopher from Toledo, OH
Parts Used:: WPY702338
Difficulty Level:: A Bit Difficult
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Screw drivers, Wrench (Adjustable)

Door seal was worn out/burned /leaking heat

Took the oven door off hinge. Took door apart pulled off old seal from inside of the inside panel of door. Replaced with new seal.

Was this instruction helpful to you?

Customer:: Horace from Las Vegas, NV
Parts Used:: WPY702338
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Screw drivers

Replaced worn seal

Remove the door. Place small screwdriver in each door arm to prevent extraction. Remove approx 20 screws. Remove the seal. Replace the new seal. you will need help in holding the seal in place until you car install at least two screws. Very straight forward. Took 20 minutes. Even a cave man can do it.

Was this instruction helpful to you?

Customer:: Camilla O from Sanford, NC
Parts Used:: WPY702338
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

range seal worn and leaking

removed front of range door. removed old seal and replaced with new seal. clean and reassemble range door. repair very simple and fast.

Was this instruction helpful to you?

All Instructions for the W214