JKP16G0J3 General Electric Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Barbara from BELLEVUE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
Twice I ordered the oven light bulb & each time the light bulb was defected
I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Olympia, WA
- Parts Used:
- WB44X200
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven bake element melted
Removed the racks, removed two screws holding the element to the back of the oven, removed two screws holding wires to the element, installed by the reverse. BUT in my case the new element still didn't heat. The part was perfect so when the old element melted and shorted, it must have damaged the controlling switch (220V requires dual pole switch--apparently one side is now bad). Since the oven is over 30 yrs old, I'm returning the element and will buy a new oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackie from Hillsboro, OR
- Parts Used:
- WB44X200
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Bake elelment was out
I turned off the breaker to the oven. Removed the old element and replaced. Turned on the oven breaker and turned the over to 350 and it was working great. I was very proud of myself as a 68 year old widow.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J T from Clarksville, TN
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Old element burned out
Turned off the power to the oven. Removed the racks. Removed two screws holding the unit to the back of the oven. Removed two screws holding the wires to the terminals. Removed the old unit. Reversed the process. Piece of cake. The only "difficulty" was that the old wire-to-terminal screws required a nut driver (as did the unit-mounting screws) while the new wire-mounting screws required a #2 Phillips screw driver. Took me a couple of minutes to get one of those from the garage.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RONALD from MT PROSPECT, IL
- Parts Used:
- WB44X200
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
BURNT-OUT ELECTRIC BAKE OVEN ELEMENT
USE A MAGNETIZED SCREW DRIVER. BE CAREFUL THE OVEN ELECTRIC WIRES DO NOT FALL BACK INSIDE OF THE OVEN. HAVE LONG NOSE PLIERS HANDY. MAKE SURE YOU TILT THE ELEMENT SO THAT THE ELEMENT TERMINALS ALIGN PROPERLY WITH THE THE SCREWS AND ELECTRIC WIRES. THAT'S IMPORTANT ELSE YOU CANNOT GET THE SCREWS STARTED TO ATTACH THE ELEMENT.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from JONESBORO, AR
- Parts Used:
- WB44X200
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Burnt into
Two 1/4 inch screws and then two Phillips head screws that was it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terrance from Fresno, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
baking element burned out
Removed the nuts securing the element to the back of the oven, pulled out the wiring and unscrewed the wires. Went on line and found the part, ordered it, received really quickly and put the part back in the oven. Works great. Oh, I also turned off the power.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Lima, OH
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The Bake Element in the oven had "blown out" on the right side, and wouldn't heat.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Then I connected the two wires to the new element with the screws provided and simply replaced the screws that hold the element in place.
In 20 minutes the job was done. It was a snap to make the repair!
Then I connected the two wires to the new element with the screws provided and simply replaced the screws that hold the element in place.
In 20 minutes the job was done. It was a snap to make the repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from TABERNACLE, NJ
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Burnt out element
As instructed in your directions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from DANVILLE, KY
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Heating element severed
Removed old new one fit perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary C from KISSIMMEE, FL
- Parts Used:
- WB44X200
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Baking element broken
Turned off the power to the stove, pulled out the racks, unscrewed the old element and pulled off the electric connectors...easy so far...installed the new element to the electric connection, pushed back into the back of the stove and reinstalled the screws. Turned on the power and then the stove...now I can bake an apple pie!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from SPARTANBURG, SC
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Burnt bake element
Removed door. Take out two hold down screws for element. Hold electrical tab with pliers and remove screw on each tab. Reverse directions to reinstall. Door may have screws to remove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from CLAYMONT, DE
- Parts Used:
- WB44X200
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
second time repaired in about ten years
removed parts from carton,,shut off breaker to over,,cradled the flash light,removed cover plate,,removed element,,removed screws from wires,,reversed to install,,screwed wires to element,,placed element in place and installed plate nuts,,,turned breaker back on...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from WINTERVILLE, GA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lights blown out
replaced lights in refrigirator and freezer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!