JKP16G0J3 General Electric Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Walter from Lake Kiowa, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Element burnt in two
I removed the two screws holding it in place,Then pulled it out so
i could remove the two wires , then connected the new unit. Replaced it in the oven wall.
Turned the oven on and it worked like a new one.
i could remove the two wires , then connected the new unit. Replaced it in the oven wall.
Turned the oven on and it worked like a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Haviland, OH
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Broken element
Removed the two screws that held the element in place. Pulled the unit out a few inches to get at the bolted wires. The hard part is reaching in the oven using bifocal lenses and trying to block out the oven light. Getting past that obstacle, the rest went very well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Chester Springs, PA
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
old element blew up
Toughest chore was to find a tool to remove the two hex screws that held the element to the back of the oven. Once I found the proper tool, the rest was easy. Pulled the circuit breaker, removed the two hex screws, disconnected the two electrical leads and put the new part in and did everything in reverse. Probably saved over $100 doing it myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Suzanne from PLAINFIELD, NJ
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The heating element was broken in one place & wouldn't heat
Ordered the part on a Friday afternoon and was shocked to receive the box on Saturday AM! Turned off the power to the unit, unscrewed the screws holding in the old element, and hooked up the new one. We didn't have a socket wrench so we subbed a pliers. So easy & cheap! Seems like everything's breaking around this house & this is the ONLY thing that was easy & cost less than $20! Happy with Parts Select!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from San Jose, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Cal Rod heating element failed
Getting the part out was easy. Turned the power off (of course) first. The outside nuts were corroded, so had to use a pair of pliers to get them off. The inside connectors were easier to get off. I had a little trouble getting the connectors on the wires. The metal part on the heating element kept wanting to bend. I finally had someone hold that in place while I made the connections. The outside screws were easy to put on. The oven now works great. I think the element was failing over a period of time, and we just didn't notice. I can't remember the last time I actually saw the element get RED hot. Works great. Thanks for your quick service and reasonable prices. Will definitely use you again, when I need parts like this. (You are now Bookmarked on my computer).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Venice, FL
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Replace Burned-out oven bake element
Used nut driver to remove old element and screw driver to remove power leads. Reversed process to install new element. Took about 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Calhoun, GA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Overn would not heat properly.
Turn circuit breaker off.
Two screws detached the unit.
Another two screws to disconnect the wires. Reversed above operation for installation.
Turn circuit breaker on.
All fixed!
P.S. Shipping was very fast.
Two screws detached the unit.
Another two screws to disconnect the wires. Reversed above operation for installation.
Turn circuit breaker on.
All fixed!
P.S. Shipping was very fast.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Wayne, OK
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Lower heating element burned out
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and replaced the two wires that hold the element in place. I received the part within about 36 hours after placing order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- arthur from annandale, VA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Old burnt out element
Removed the two screws holding the mount and then reattached the two wires to the element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William M. from Towaco, NJ
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake element went dead
Removed access screws from bake element cover, removed screws retaining wire connections on bake element, reverse procedure, and heat to burn off contaminants.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norman from Houston, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Oven bake element broken
Took out the old (removed 2 screws holding the element to the back of the oven, disconnected the 2 screws attaching the electrical wires to the element). Decided to clean the oven with EasyOff. It took longer to spray this on, and then later wipe it up, than the repair itself. Reversed the procedure for the new element. A very simple repair - my wife is amazed!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jerome from Farmington Hills, MI
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
heating element was on fire and needed to be replaced
shut off circuitbreaker.removed two screws.kind of hard since screws were 25 years old and were tight.then i removed the oven door and pulled out the elementout and removed two more screws that held the wires to the element,then removed the element and replaced the new one and screwed it to the wires and thenthe next two screws that held the element in place. turn on the circuitbreaker and it was a miracle it got hot!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Norcross, GA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
replace burned out element
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires..Took out the old element and reversed tjhe procedure to install the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeanne from bodega bay, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
bake element was fried
husband said he would call repairman. I found you and ordered part. By the time my husband got around to calling the repairman, I was finished.
Only trouble was getting my hands to work in the small space. The cover plate was not as big as the former unit so I had to muscle it on. BUT, it was a very easy process and we saved tons of money on a repairman and a new oven/micro. THANKS.
Only trouble was getting my hands to work in the small space. The cover plate was not as big as the former unit so I had to muscle it on. BUT, it was a very easy process and we saved tons of money on a repairman and a new oven/micro. THANKS.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Candice from Houston, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Bottom element caught fire and burned out.
You website was quite easy to use and we found the part really quickly. After we ordered it, it was delivered within 5 days and was easy to install. I was a happy camper to have my oven back which I use a lot. Thanks for the quick delivery and information. Candi
Was this instruction helpful to you?
Thank you for voting!